- 您現在的位置：買賣IC網 > PDF目錄377777 > LTC1960 (Linear Technology Corporation) 4A, High Efficiency, Standalone Li Battery Charger PDF資料下載
參數資料
| 型號： | LTC1960 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 4A, High Efficiency, Standalone Li Battery Charger |
| 中文描述： | 第4A，高效，獨立鋰電池充電器 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 241K |
| 代理商： | LTC1960 |
8
LTC4007
4007i
TEST CIRCUIT
–
+
–
+
EA
LT1055
LTC4007
V
REF
CHEM
3C4C
BAT
DIVIDER/
MUX
16
7
15
ITH
0.6V
4007 TC
10
OPERATIOU
Overview
The LTC4007 is a synchronous current mode PWM step-
down (buck) switcher battery charger controller. The
charge current is programmed by the combination of a
program resistor (R
PROG
) from the PROG pin to ground
and a sense resistor (R
SENSE
) between the CSP and BAT
pins. The final float voltage is programmed to one of four
values (12.3V, 12.6V, 16.4V, 16.8V) with
±
1% maximum
accuracy using pins 3C4C and CHEM. Charging begins
when the potential at the DCIN pin rises above the voltage
at BAT (and the UVLO voltage) and the SHDN pin is low; the
CHG pin is set low. At the beginning of the charge cycle, if
the cell voltage is below 2.5V (2.44V if CHEM is low), the
LOBAT pin will be low. The LOBAT indicator can be used
to reduce the charging current to a low value, typically
10% of full scale. If the cell voltage stays below 2.5V for
25% of the total charge time, the charge sequence will be
terminated immediately and the FAULT pin will be set low.
An external thermistor network is sampled at regular
intervals. If the thermistor value exceeds design limits,
charging is suspended and the FAULT pin is set low. If the
thermistor value returns to an acceptable value, charging
resumes and the FAULT pin is set high. An external resistor
on the R
T
pin sets the total charge time. The timer can be
defeated by forcing the CHG pin to a low voltage.
As the battery approaches the final float voltage, the
charge current will begin to decrease. When the current
drops to 10% of the full-scale charge current, an internal
C/10 comparator will indicate this condition by latching
the FLAG pin low. The charge timer is also reset to 1/4 of
the total charge time when FLAG goes low. If this condition
is caused by an input current limit condition, described
below, then the FLAG indicator will be inhibited. When a
time-out occurs, charging is terminated immediately and
the CHG pin is forced to a high impedance state. The
charger will automatically restart if the cell voltage is
below 3.9V (or 3.81V if CHEM is low). To restart the charge
cycle manually, simply remove the input voltage and
reapply it, or set the SHDN pin high momentarily. When
the input voltage is not present, the charger goes into a
sleep mode, dropping battery current drain to 15
μ
A. This
greatly reduces the current drain on the battery and
increases the standby time. The charger is inhibited any
time the SHDN pin is high.
Input FET
The input FET circuit performs two functions. It enables
the charger if the input voltage is higher than the CLN pin
and provides the logic indicator of AC present on the ACP
pin. It controls the gate of the input FET to keep a low
forward voltage drop when charging and also prevents
reverse current flow through the input FET.
If the input voltage is less than V
CLN
, it must go at least
170mV higher than V
CLN
to activate the charger. When this
occurs the ACP pin is released and pulled up with an
external load to indicate that the adapter is present. The
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3711 | 4A, High Efficiency, Standalone Li Battery Charger |
| LTC4008 | 4A, High Efficiency, Standalone Li Battery Charger |
| LTC4010 | High Efficiency Standalone Nickel Battery Charger |
| LTC4010EFE | High Efficiency Standalone Nickel Battery Charger |
| LTC4052-42 | Lithium-Ion Battery Pulse Charger with Overcurrent Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1960CG | 功能描述:IC BATT CHRGR/SELECTR DUAL36SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1960CG#PBF | 功能描述:IC BATT CHRGR/SELECTR DUAL36SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC1960CG#TR | 功能描述:IC BATT CHRGR/SELECTR DUAL36SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1960CG#TRPBF | 功能描述:IC BATT CHRGR/SELECTR DUAL36SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1960CUHF#PBF | 功能描述:IC BATT CHRGR/SELECTR DL 38-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。