- 您現在的位置：買賣IC網 > PDF目錄369850 > LTC1957-2EMS AMP POWER CONTROLLER PDF資料下載
參數資料
| 型號： | LTC1957-2EMS |
| 英文描述： | AMP POWER CONTROLLER |
| 中文描述： | 安培電源控制器 |
| 文件頁數： | 23/28頁 |
| 文件大?。?/td> | 389K |
| 代理商： | LTC1957-2EMS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁
23
LTC1929/LTC1929-PG
con
tinuous mode will be highest at the maximum input
voltage since the duty factor is <50%. The maximum
output current ripple is:
I
V
fL
at
DF
I
V
(
kHz
H
A
m
V
A
mV
COUT
OUT
COUTMAX
RMS
OUTRIPPLE
RMS
RMS
=
( )
=
(
=
=
)
μ
)
)
=
0 3
.
33
1.
300
1 5
.
0 3
.
1 2
20
1 2
.
24
%
.
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of the
LTC1929. These items are also illustrated graphically in
the layout diagram of Figure11. Check the following in
your layout:
1) Are the signal and power grounds segregated The
LTC1929 signal ground pin should return to the (–) plate
of C
OUT
separately. The power ground returns to the
sources of the bottom N-channel MOSFETs, anodes of the
Schottky diodes, and (–) plates of C
IN
, which should have
as short lead lengths as possible.
2) Does the LTC1929 V
OS+
pin connect to the (+) plate(s)
of C
OUT
Does the LTC1929 V
OS–
pin connect to the (–)
plate(s) of C
OUT
The resistive divider R1, R2 must be
connected between the V
DIFFOUT
and signal ground and
any feedforward capacitor across R1 should be as close as
possible to the LTC1929.
3) Are the SENSE
–
and SENSE
+
leads routed together with
minimum PC trace spacing The filter capacitors between
SENSE
+
and SENSE
–
pin pairs should be as close as
possible to the LTC1929. Ensure accurate current sensing
with Kelvin connections.
4) Do the (+) plates of C
IN
connect to the drains of the
topside MOSFETs as closely as possible This capacitor
provides the AC current to the MOSFETs. Keep the input
current path formed by the input capacitor, top and bottom
MOSFETs, and the Schottky diode on the same side of the
PC board in a tight loop to minimize conducted and
radiated EMI.
5) Is the INTV
CC
1
μ
F ceramic decoupling capacitor con-
nected closely between
INTV
CC
and the power ground pin
This capacitor carries the MOSFET driver peak currents. A
small value is used to allow placement immediately adja-
cent to the IC.
6) Keep the switching nodes, SW1 (SW2), away from
sensitive small-signal nodes. Ideally the switch nodes
should be placed at the furthest point from the LTC1929.
7) Use a low impedance source such as a logic gate to drive
the PLLIN pin and keep the lead as short as possible.
The diagram in Figure 9 illustrates all branch currents in
a 2-phase switching regulator. It becomes very clear after
studying the current waveforms why it is critical to keep
the high-switching-current paths to a small physical size.
High electric and magnetic fields will radiate from these
“l(fā)oops” just as radio stations transmit signals. The out-
put capacitor ground should return to the negative termi-
nal of the input capacitor and not share a common
ground path with any switched current paths. The left half
of the circuit gives rise to the “noise” generated by a
switching regulator. The ground terminations of the
synchronous MOSFETs and Schottky diodes should re-
turn to the bottom plate(s) of the input capacitor(s) with
a short isolated PC trace since very high switched cur-
rents are present. A separate isolated path from the
bottom plate(s) of the input capacitor(s) should be used
to tie in the IC power ground pin (PGND) and the signal
ground pin (SGND). This technique keeps inherent sig-
nals generated by high current pulses from taking alter-
nate current paths that have finite impedances during the
total period of the switching regulator. External OPTI-
LOOP compensation allows overcompensation for PC
layouts which are not optimized but this is not the
recommended design procedure.
APPLICATIU
W
U
U
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| LTC25501PAK | Optoelectronic |
| LTC25601PAK | Optoelectronic |
| LTC3405AES6 | Analog IC |
| LTC5502A1P12 | Optoelectronic |
| LTC5612ELM | Optoelectronic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1957-2EMS#PBF | 功能描述:IC RF PWR CONTROLLR DUAL 10-MSOP RoHS:是 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX |
| LTC1957-2EMS#TR | 功能描述:IC RF PWR CONTROLLR DUAL 10-MSOP RoHS:否 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX |
| LTC1957-2EMS#TRPBF | 功能描述:IC RF PWR CONTROLLR DUAL 10-MSOP RoHS:是 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX |
| LTC1960CG | 功能描述:IC BATT CHRGR/SELECTR DUAL36SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1960CG#PBF | 功能描述:IC BATT CHRGR/SELECTR DUAL36SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
發布緊急采購，3分鐘左右您將得到回復。