- 您現在的位置：買賣IC網 > PDF目錄377766 > LTC1955EUH (LINEAR TECHNOLOGY CORP) Dual Smart Card Interface with Serial Control PDF資料下載
參數資料
| 型號： | LTC1955EUH |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Dual Smart Card Interface with Serial Control |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| 封裝： | 5 X 5 MM, 0.75 MM HEIGHT, MO-220WHHD, QFN-32 |
| 文件頁數： | 12/20頁 |
| 文件大?。?/td> | 259K |
| 代理商： | LTC1955EUH |
LTC1955
12
sn1955 1955fs
Smart Card Detection Circuits
The PRES A/PRES B pins are used to detect the presence
of a smart card. An automatic debounce circuit waits until
a smart card has been present for a continuous period of
typically 35ms. Once a valid card indication exists, the
status bit for that channel is updated and may be polled by
cycling data through the serial port. The D
OUT
pin (equiva-
lent to D15) of the serial port can be used to indicate the
presence of a card on channel A in real time if LD is held
low.
The PRES A/PRES B pins have built-in pull-up current
sources so no external components are required for
switch detection. The pull-up current sources are de-
signed to have a small current when the pin voltage is
below approximately 1V but somewhat higher current
when the pin voltage reaches 1V. This helps maintain low
power dissipation when a card is present and yet fast
response time to a card removal.
The PRES A/PRES B pins can be configured to respond to
either normally open or normally closed switches via the
NC/NO pin.
Activation/Deactivation
For maximum flexibility, the activation sequencing of the
smart card is left to the application programmer. Upon
activation, to comply with relevant smart card standards,
none of the smart card signal pins will be allowed to go
high before the smart card supply voltage (V
CCA
/V
CCB
) has
reached its final value. Deactivation can be achieved either
manually or automatically. An electrical fault condition will
trigger the automatic deactivation.
Manual deactivation may be performed under software
control by setting the smart card pins to 0V in the desired
sequence via the control pins (SYNC, ASYNC, R
IN
, DATA
and the serial port). For most applications this will be
cumbersome and the built-in deactivation will be used
instead.
Automatic Deactivation
The built-in deactivation sequence can be executed via the
serial port simply by setting the appropriate control bits
(D0 and D1 or D8 and D9) to 0. The deactivation sequence
is outlined below.
1. The RST A/RST B pin for that channel is immediately
brought low.
2. The deactivation of the CLK A/CLK B pins depends upon
which type of card is used:
If the smart card was set to asynchronous mode then
the CLK A/CLK B pin will be latched low on its next falling
edge. If no falling edges occur within 5
μ
s (min) then the
CLK A/CLK B line is forced low.
If the smart card was set to synchronous mode then the
CLK A/CLK B pin is immediately latched at its current
value (either high or low) and then forced low after a
duration of 5
μ
s (min). During the 5
μ
s timeout period
changes on SYNC will be ignored.
3. The I/O A/I/O B, C4A and C8A pins for that channel are
brought low.
4. The V
CCA
/V
CCB
pin is brought low.
If an error occurs on one smart card, operation of the other
card is unaffected.
OPERATIOU
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1957 | 40MHz to 900MHz Quadrature Demodulator |
| LT5500 | 40MHz to 900MHz Quadrature Demodulator |
| LT5511 | 40MHz to 900MHz Quadrature Demodulator |
| LT5515 | 40MHz to 900MHz Quadrature Demodulator |
| LT5517 | 40MHz to 900MHz Quadrature Demodulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1955EUH#PBF | 功能描述:IC INTERFACE DL SMART CARD 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC1955EUH#TR | 功能描述:IC SMART CARD INTERFC DUAL 32QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC1955EUH#TRPBF | 功能描述:IC INTERFACE DL SMART CARD 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC1955IUH#PBF | 功能描述:IC SMART CARD INTERFACE DL 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC1955IUH#TRPBF | 功能描述:IC SMART CARD INTERFACE DL 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
發布緊急采購，3分鐘左右您將得到回復。