- 您現在的位置：買賣IC網 > PDF目錄2005 > LTC1859IG#TRPBF (Linear Technology)IC A/D CONV 8CH 16BIT 28-SSOP PDF資料下載
參數資料
| 型號： | LTC1859IG#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 2/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC A/D CONV 8CH 16BIT 28-SSOP |
| 標準包裝： | 2,000 |
| 系列： | SoftSpan™ |
| 位數： | 16 |
| 采樣率（每秒）： | 100k |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 40mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極 |
| 配用： | DC682A-ND - BOARD SAR ADC LTC1859 |
LTC1857/LTC1858/LTC1859
10
185789fa
OPERATION
OVERVIEW
The LTC1857/LTC1858/LTC1859 are innovative, multichan-
nel ADCs that provide software-selectable input ranges for
each of their eight input channels. Using on-chip resistors
and switches, it provides an attenuation and offset that can
be programmed for each channel on the y. The precisely
trimmed attenuators ensure accurate input ranges. Because
they precede the multiplexer, errors due to multiplexer
on-resistance are eliminated.
The input word that selects the input channel also selects
the desired input range for that channel. The available
ranges are 0V to 5V, 0V to 10V (unipolar), ±5V and ±10V
(bipolar). They are achieved with the ADC running on a
single 5V supply. In addition to the range selection, single
ended or differential inputs may be selected for each chan-
nel or pair of channels. Finally, overrange protection is
provided for unselected channels. An overrange condition
on an unused channel will not affect the conversion result
on the selected channel.
CONVERSION DETAILS
The LTC1857/LTC1858/LTC1859 use a successive ap-
proximation algorithm and an internal sample-and-hold
circuit to convert an analog signal to a 12-/14-/16-bit serial
output respectively. The ADCs are complete with a precision
reference and an internal clock. The control logic provides
easy interface to microprocessors and DSPs. (Please refer
to the Digital Interface section for the data format.)
The analog signals applied at the MUX input channels are
rescaled by the resistor divider network formed by R1, R2
and R3 as shown below. The rescaled signals appear on
the MUXOUT (Pins 10, 11) which are also connected to
the ADC inputs (Pins 12, 13) under normal operation.
Before starting a conversion, an 8-bit data word is clocked
into the SDI input on the rst eight rising SCK edges to
select the MUX address, input range and power down
mode. The ADC enters acquisition mode on the falling
edge of the sixth clock in the 8-bit data word and ends
on the rising edge of the CONVST signal which also starts
a conversion (see Figure 7). A minimum time of 4μs will
provide enough time for the sample-and-hold capacitors
to acquire the analog signal. Once a conversion cycle has
begun, it cannot be restarted.
During the conversion, the internal differential 12-/14-
/16-bit capacitive DAC output is sequenced by the SAR from
the most signicant bit (MSB) to the least signicant bit
(LSB). The input is successively compared with the binary
weighted charges supplied by the differential capacitive
DAC. Bit decisions are made by a high speed comparator.
At the end of a conversion, the DAC output balances the
analog input (ADC+ – ADC–). The SAR contents (a 16-bit
data word) which represents the difference of ADC+ and
ADC– are loaded into the 12-/14-/16-bit shift register.
DRIVING THE ANALOG INPUTS
The nominal input ranges for the LTC1857/LTC1858/
LTC1859 are 0V to 5V, 0V to 10V, ±5V and ±10V and the
MUX inputs are overvoltage protected to ± 25V. The input
impedance is typically 42kΩ in unipolar mode and 31kΩ
in bipolar mode, therefore, it should be driven with a low
impedance source. Wideband noise coupling into the input
can be minimized by placing a 3000pF capacitor at the input
as shown in Figure 2. An NPO-type capacitor gives the
lowest distortion. Place the capacitor as close to the device
input pin as possible. If an amplier is to be used to drive
the input, care should be taken to select an amplier with
adequate accuracy, linearity and noise for the application.
The following list is a summary of the op amps that are
suitable for driving the LTC1857/LTC1858/LTC1859. More
detailed information is available in the Linear Technology
data books and online at www.linear.com.
LT1007: Low noise precision amplier. 2.7mA supply
current ±5V to ±15V supplies. Gain bandwidth product
8MHz. DC applications.
MUX
INPUT
R1
25k
REFCOMP
CH SEL
R3
10k
1859 AI03
R2
17k
MUXOUT
BIPOLAR
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1867AIGN#TRPBF | IC ADC 16BIT 8CH 200KSPS 16SSOP |
| LTC1867LCGN#PBF | IC ADC 16BIT 8CH 175KSPS 16SSOP |
| LTC2142IUP-14#PBF | IC ADC DUAL 14BIT 65MSPS 64QFN |
| LTC2143CUP-14#PBF | IC ADC DUAL 14BIT 80 MSPS 64-QFN |
| LTC2153IUJ-14#PBF | IC ADC 14BIT DUAL 310MSPS 40QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1860CMS8 | 功能描述:IC A/D CONV 1CH 12BIT 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC1860CMS8#PBF | 功能描述:IC A/D CONV 1CH 12BIT 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1860CMS8#TR | 功能描述:IC A/D CONV 1CH 12BIT 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC1860CMS8#TRPBF | 功能描述:IC A/D CONV 1CH 12BIT 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC1860CS8 | 功能描述:IC A/D CONV 1CH 12BIT 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。