- 您現在的位置：買賣IC網 > PDF目錄377764 > LTC1859 (Linear Integrated Systems) 8-Channel, 12-/14-/16-Bit, 100ksps SoftSpan A/D Converters with Shutdown PDF資料下載
參數資料
| 型號： | LTC1859 |
| 廠商： | Linear Integrated Systems |
| 英文描述： | 8-Channel, 12-/14-/16-Bit, 100ksps SoftSpan A/D Converters with Shutdown |
| 中文描述： | 8通道，12-/14-/16-Bit，100ksps的具有關斷SoftSpan的A / D轉換器 |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 265K |
| 代理商： | LTC1859 |
16
LTC1857/LTC1858/LTC1859
185789f
APPLICATIOU
MUX ADDRESS
The first four bits of the input word assign the MUX
configuration for the requested conversion. For a given
channel selection, the converter will measure the voltage
between the two channels indicated by the + and – signs
in the selected row of Table 1. Note that in differential
mode (SGL/DIFF = 0) measurements are limited to four
adjacent input pairs with either polarity. In single-ended
mode, all input channels are measured with respect to
COM. Both the “+” and “–” inputs are sampled simulta-
neously so common mode noise is rejected.
W
U
U
INPUT RANGE (UNI, GAIN)
The fifth and sixth input bits (UNI, GAIN) determine the
input range for the conversion. When UNI is a logical one,
a unipolar conversion will be performed. When UNI is a
logical zero, a bipolar conversion will result. The GAIN
input bit determines the input span for the conversion.
When GAIN is a logical one, either 0V to 10V or
±
10V input
spans will be selected depending on UNI. When GAIN is a
logical zero, either 0V to 5V or
±
5V input spans will be
chosen. The input ranges for different UNI and GAIN
inputs are shown in Table 2.
Table 2. Input Range Selection
UNI
0
1
0
1
GAIN
0
0
1
1
INPUT RANGE
±
5V
0V to 5V
±
10V
0V to 10V
P
OWER DOWN SELECTION (NAP, SLEEP)
The last two bits of the input word (Nap and Sleep) deter-
mine the power shutdown mode of the LTC1857/LTC1858/
LTC1859. See Table 3. Nap mode is selected when Nap =
1 and Sleep = 0. The previous conversion result will be
clocked out and a conversion will occur before entering
the Nap mode. The Nap mode starts at the end of the con-
version which is indicated by the rising edge of the BUSY
signal. Nap mode lasts until the falling edge of the 2nd SCK
(see Figure 9). Automatic nap will be achieved if Nap = 1
is selected each time an input word is written to the ADC.
Table 3. Power Down Selection
NAP
0
1
X
SLEEP
0
0
1
POWER DOWN MODE
Power On
Nap
Sleep
Sleep mode will occur when Sleep = 1 is selected,
regardless of the selection of the Nap input. The previous
conversion result can be clocked out and the Sleep mode
will start on the falling edge of the last (16th) SCK. Notice
that the CONVST should stay either high or low in sleep
mode (see Figure 10). To wake up from the sleep mode,
apply a rising edge on the CONVST signal and then apply
Sleep = 0 on the next SDI word and the part will wake up
on the falling edge of the last (16th) SCK (see Figure 11).
In Sleep mode, all bias currents are shut down and only the
power on reset circuit and leakage currents (about 10
μ
A)
remain. Sleep mode wake-up time is dependent on the
value of the capacitor connected to the REFCOMP (Pin 16).
The wake-up time is typically 40ms with the recom-
mended 10
μ
F capacitor connected on the REFCOMP pin.
DYNAMIC PERFORMANCE
FFT (Fast Fourier Transform) test techniques are used to
test the ADC’s frequency response, distortion and noise
at the rated throughput. By applying a low distortion sine
wave and analyzing the digital output using an FFT
algorithm, the ADC’s spectral content can be examined
for frequencies outside the fundamental. Figure 12 shows
a typical LTC1859 FFT plot which yields a SINAD of 87dB
and THD of –101dB.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1859CG | 8-Channel, 12-/14-/16-Bit, 100ksps SoftSpan A/D Converters with Shutdown |
| LTC1859IG | 8-Channel, 12-/14-/16-Bit, 100ksps SoftSpan A/D Converters with Shutdown |
| LTC1867AIGN | Quadruple 2-Input Positive-AND Gate 14-TVSOP -40 to 85 |
| LTC1851 | 12-/16-Bit, 8-Channel 200ksps ADCs |
| LTC1852 | 12-/16-Bit, 8-Channel 200ksps ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1859CG | 制造商:Linear Technology 功能描述:ADC Single SAR 100ksps 16-bit Serial 28-Pin SSOP |
| LTC1859CG#PBF | 功能描述:IC ADC 8CH 16BIT 100KSPS 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:SoftSpan™ 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1859CG#TRPBF | 功能描述:IC A/D CONV 8CH 16BIT 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:SoftSpan™ 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1859CGPBF | 制造商:Linear Technology 功能描述:ADC,LTC1859 16bit 100kSPS 8 ch SPI SSOP |
| LTC1859IG#PBF | 功能描述:IC A/D CONV 8CH 16BIT 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:SoftSpan™ 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。