- 您現在的位置：買賣IC網 > PDF目錄377764 > LTC1858IG (Linear Integrated Systems) 8-Channel, 12-/14-/16-Bit, 100ksps SoftSpan A/D Converters with Shutdown PDF資料下載
參數資料
| 型號： | LTC1858IG |
| 廠商： | Linear Integrated Systems |
| 英文描述： | 8-Channel, 12-/14-/16-Bit, 100ksps SoftSpan A/D Converters with Shutdown |
| 中文描述： | 8通道，12-/14-/16-Bit，100ksps的具有關斷SoftSpan的A / D轉換器 |
| 文件頁數： | 10/20頁 |
| 文件大小： | 265K |
| 代理商： | LTC1858IG |
10
LTC1857/LTC1858/LTC1859
185789f
APPLICATIOU
OVERVIEW
The LTC1857/LTC1858/LTC1859 are innovative, multi-
channel ADCs that provide software-selectable input ranges
for each of their eight input channels. Using on-chip
resistors and switches, it provides an attenuation and
offset that can be programmed for each channel on the fly.
The precisely trimmed attenuators ensure accurate input
ranges. Because they precede the multiplexer, errors due
to multiplexer on-resistance are eliminated.
The input word that selects the input channel also selects
the desired input range for that channel. The available
ranges are 0V to 5V, 0V to 10V (unipolar),
±
5V and
±
10V
(bipolar). They are achieved with the ADC running on a
single 5V supply. In addition to the range selection, single
ended or differential inputs may be selected for each
channel or pair of channels. Finally, overrange protection
is provided for unselected channels. An overrange condi-
tion on an unused channel will not affect the conversion
result on the selected channel.
W
U
U
CONVERSION DETAILS
The LTC1857/LTC1858/LTC1859 use a successive approxi-
mation algorithm and an internal sample-and-hold circuit
to convert an analog signal to a 12-/14-/16-bit serial out-
put respectively. The ADCs are complete with a precision
reference and an internal clock. The control logic provides
easy interface to microprocessors and DSPs. (Please refer
to the Digital Interface section for the data format.)
The analog signals applied at the MUX input channels are
rescaled by the resistor divider network formed by R1, R2
and R3 as shown below. The rescaled signals appear on
the MUXOUT (Pins 10, 11) which are also connected to the
ADC inputs (Pins 12, 13) under normal operation.
Before starting a conversion, an 8-bit data word is clocked
into the SDI input on the first eight rising SCK edges to
select the MUX address, input range and power down
mode. The ADC enters acquisition mode on the falling
edge of the sixth clock in the 8-bit data word and ends on
the rising edge of the CONVST signal which also starts a
conversion (see Figure 7). A minimum time of 4
μ
s will
provide enough time for the sample-and-hold capacitors
to acquire the analog signal. Once a conversion cycle has
begun, it cannot be restarted.
During the conversion, the internal differential 12-/14-/
16-bit capacitive DAC output is sequenced by the SAR from
the most significant bit (MSB) to the least significant bit
(LSB). The input is successively compared with the binary
weighted charges supplied by the differential capacitive
DAC. Bit decisions are made by a high speed comparator.
At the end of a conversion, the DAC output balances the
analog input (ADC
+
– ADC
–
). The SAR contents (a 16-bit
data word) which represents the difference of ADC
+
and
ADC
–
are loaded into the 12-/14-/16-bit shift register.
DRIVING THE ANALOG INPUTS
The nominal input ranges for the LTC1857/LTC1858/
LTC1859 are 0V to 5V, 0V to 10V,
±
5V and
±
10V and the
MUX inputs are overvoltage protected to
±
25V. The input
impedance is typically 42k
in unipolar mode and 31k
in bipolar mode, therefore, it should be driven with a low
impedance source. Wideband noise coupling into the
input can be minimized by placing a 3000pF capacitor at
the input as shown in Figure 2. An NPO-type capacitor
gives the lowest distortion. Place the capacitor as close to
the device input pin as possible. If an amplifier is to be used
to drive the input, care should be taken to select an
amplifier with adequate accuracy, linearity and noise for
the application. The following list is a summary of the op
amps that are suitable for driving the LTC1857/LTC1858/
LTC1859. More detailed information is available in the
Linear Technology data books and online at
www.linear.com.
LT
1007: Low noise precision amplifier. 2.7mA supply
current
±
5V to
±
15V supplies. Gain bandwidth product
8MHz. DC applications.
MUX
INPUT
R1
25k
REFCOMP
CH SEL
R3
10k
1859 AI03
R2
17k
MUXOUT
BIPOLAR
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1859 | 8-Channel, 12-/14-/16-Bit, 100ksps SoftSpan A/D Converters with Shutdown |
| LTC1859CG | 8-Channel, 12-/14-/16-Bit, 100ksps SoftSpan A/D Converters with Shutdown |
| LTC1859IG | 8-Channel, 12-/14-/16-Bit, 100ksps SoftSpan A/D Converters with Shutdown |
| LTC1867AIGN | Quadruple 2-Input Positive-AND Gate 14-TVSOP -40 to 85 |
| LTC1851 | 12-/16-Bit, 8-Channel 200ksps ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1858IG#PBF | 功能描述:IC A/D CONV 8CH 14BIT 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:SoftSpan™ 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1858IG#TRPBF | 功能描述:IC A/D CONV 8CH 14BIT 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:SoftSpan™ 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1859CG | 制造商:Linear Technology 功能描述:ADC Single SAR 100ksps 16-bit Serial 28-Pin SSOP |
| LTC1859CG#PBF | 功能描述:IC ADC 8CH 16BIT 100KSPS 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:SoftSpan™ 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1859CG#TRPBF | 功能描述:IC A/D CONV 8CH 16BIT 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:SoftSpan™ 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。