- 您現在的位置：買賣IC網 > PDF目錄377764 > LTC1840CGN (LINEAR TECHNOLOGY CORP) Dual Fan Controller with 2-Wire Interface PDF資料下載
參數資料
| 型號： | LTC1840CGN |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Dual Fan Controller with 2-Wire Interface |
| 中文描述： | BRUSH DC MOTOR CONTROLLER, PDSO16 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP-16 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 203K |
| 代理商： | LTC1840CGN |
LTC1840
5
1840f
fault conditions on the LTC1840. An external 10k pull-up
is recommended.
GPIO1, GPIO2, GPIO3, GPIO4 (Pins 6, 7, 9, 10):
General
Purpose Inputs/Outputs. These pins can be used as digital
inputs with CMOS logic thresholds or digital outputs/LED
drivers with open drain pull-downs that can be pro-
grammed to blink. GPIO pins can be programmed to
produce faults due to changes in their logic states, and
these faults can only be cleared by software or powering
the LTC1840 down. All GPIOs default to nonfaulting logic
inputs upon power-up and their functionality is changed
through the serial interface.
GND (Pin 8):
Ground. Connect to analog ground plane.
TACHA (Pin 11):
Tachometer Input A. This pin is a digital
input that is designed to interface to the tachometer output
from a 3-wire fan. Internal logic counts between rising
TACHA edges at serially programmable frequencies of
25kHz, 12.5kHz, 6.25kHz or 3.125kHz and the most re-
cently completed count is stored in a register accessible
through the serial interface. The maximum count is 255
and the LTC1840 is programmable to produce faults when
a count exceeds this number. This pin has CMOS thresh-
olds and the default conditions are to count at 3.125kHz
and to not produce faults.
TACHB (Pin 12):
Tachometer Input B. See TACHA
PIU
SCL (Pin 1):
Serial Clock Input. The 2-wire bus master
device clocks this pin at a frequency between 0kHz and
100kHz to enable serial bus communications. Data at the
SDA pin is shifted in or out on rising SCL edges. SCL has
a logic threshold of 1V and an external pull-up resistor or
current source is normally required.
SDA (Pin 2):
Serial Data Input. This is a bidirectional data
pin which normally has an external pull-up resistor or
current source and can be pulled down by the open drain
device on the LTC1840 or by external devices. The master
controls SDA during addressing, the writing of data, and
read acknowledgment, while the LTC1840 controls SDA
when data is being read back and during write acknowl-
edgment. SDA data is shifted in or out on rising SCL edges.
SDA has a logic threshold of 1V.
A1 (Pin 3):
Three State Address Programming Input. This
pin can cause three different logic states internally, de-
pending upon whether it is pulled to supply, pulled to
ground, or not connected (NC). Combined with the A0 pin,
this provides for nine different possible two-wire bus
addresses for the LTC1840 (see Table 1).
A0 (Pin 4):
Three State Address Programming Input. See
A1.
FAULT (Pin 5):
Fault Indicator Pull-Down Output. This pin
has an open drain pull-down that is used to signal various
TYPICAL PERFOR U
CODE
0
B
0.4
0.3
0.2
0.1
0
–0.1
–0.2
255
1840 G10
T
A
= 25
°
C
TEMPERATURE (
°
C)
–50
–25
25
75
B
50
1.011
1.010
1.009
1.008
1.007
1.006
1.005
1.004
1.003
1.002
1840 G11
0
100
BLAST Falling Threshold
at V
CC
= 3V
DAC INL at V
CC
= 3V
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1840IGN | Dual Fan Controller with 2-Wire Interface |
| LTC1840 | RSO-S_D(Z) Series - Econoline Regulated DC-DC Converters; Input Voltage (Vdc): 12V; Output Voltage (Vdc): 05V; Power: 1W; 2:1 and 4:1 Wide Input Voltage Ranges; 1kVDC, 2kVD & 3kVDC Isolation; UL94V-0 Package Material; Continuous Short Circuit Protectionwith Current Foldback; Low Noise; No External Capacitor needed; Efficiency to 83% |
| LTC1842C | Quadruple 2-Input Positive-NAND Gate 14-VQFN -40 to 85 |
| LTC1842 | Ultralow Power Dual Comparators with Reference |
| LTC1843I | Hex Inverter 14-SOIC -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1840CGN#PBF | 功能描述:IC CTLR DUAL FAN 2WIRE 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 產品變化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 標準包裝:1 系列:- 應用:DC 電機控制器，無刷（BLDC），3 相 評估套件:可供 輸出數:1 電流 - 輸出:100mA 電壓 - 負載:5.25 V ~ 20 V 電源電壓:5.25 V ~ 20 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-VQFN（7x7） 包裝:剪切帶 (CT) 其它名稱:ATA6833-PLQWCT |
| LTC1840CGN#TR | 功能描述:IC DUAL FAN CONTROLLER 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 產品變化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 標準包裝:1 系列:- 應用:DC 電機控制器，無刷（BLDC），3 相 評估套件:可供 輸出數:1 電流 - 輸出:100mA 電壓 - 負載:5.25 V ~ 20 V 電源電壓:5.25 V ~ 20 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-VQFN（7x7） 包裝:剪切帶 (CT) 其它名稱:ATA6833-PLQWCT |
| LTC1840CGN#TRPBF | 功能描述:IC DUAL FAN CONTROLLER 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 產品變化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 標準包裝:1 系列:- 應用:DC 電機控制器，無刷（BLDC），3 相 評估套件:可供 輸出數:1 電流 - 輸出:100mA 電壓 - 負載:5.25 V ~ 20 V 電源電壓:5.25 V ~ 20 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-VQFN（7x7） 包裝:剪切帶 (CT) 其它名稱:ATA6833-PLQWCT |
| LTC1840IGN | 功能描述:IC DUAL FAN CONTROLLER 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| LTC1840IGN#PBF | 功能描述:IC DUAL FAN CONTROLLER 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
發布緊急采購，3分鐘左右您將得到回復。