- 您現在的位置：買賣IC網 > PDF目錄377763 > LTC1733EMSE (LINEAR TECHNOLOGY CORP) Monolithic Linear Lithium-Ion Battery Charger with Thermal Regulation PDF資料下載
參數資料
| 型號： | LTC1733EMSE |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Monolithic Linear Lithium-Ion Battery Charger with Thermal Regulation |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | PLASTIC, MSOP-10 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 169K |
| 代理商： | LTC1733EMSE |
LTC1733
13
sn1733 1733fs
Stability
The constant-voltage mode feedback loop is stable
without any compensation when a battery is connected.
However, a 1
μ
F capacitor with a 1
series resistor to GND
is recommended at the BAT pin to keep ripple voltage low
when the battery is disconnected.
In the constant-current mode it is the PROG pin that is in
the feedback loop and not the battery. The constant-
current mode stability is affected by the impedance at the
PROG pin. With no additional capacitance on the PROG
pin, stability is acceptable with program resistor values as
high as 50k. However, additional capacitance on this node
reduces the maximum allowed program resistor. The pole
frequency at the PROG pin should be kept above 500kHz.
Therefore, if the PROG pin is loaded with a capacitance, C,
the following equation should be used to calculate the
maximum resistance value for R
PROG
:
R
PROG
< 1/(6.283 500E3 C)
Average, rather than instantaneous, battery current may
be of interest to the user. For example, if a switching power
supply operating in low-current mode is connected in
parallel with the battery the average current being pulled
out of the BAT pin is typically of more interest than the
instantaneous current pulses. In such a case, a simple RC
filter can be used on the PROG pin to measure the average
battery current as shown in Figure 4. A 10k resistor is
added between the PROG pin and the filter capacitor and
monitoring circuit to ensure stability.
5
7
R
PROG
C
FILTER
CHARGE
CURRENT
MONITOR
CIRCUITRY
10k
LTC1733
1733 F04
GND
PROG
Figure 4. Isolating Capacitive Load on PROG Pin and Filtering.
APPLICATIOU
W
U
U
I
C
C
C W
°
/
V
V
C
/
C A
°
A
BAT
=
°
°
=
°
=
105
–3 75
55
40
)
5
(
50
50
1
–
Furthermore, the voltage at the PROG pin will change
proportionally with the charge current as discussed in the
Programming Charge Current section.
It is important to remember that LTC1733 applications do
not need to be designed for worst-case thermal conditions
since the IC will automatically reduce power dissipation
when the junction temperature reaches approximately
105
°
C. See Design Note 283 for additional information.
Board Layout Considerations
In order to be able to deliver maximum charge current
under all conditions, it is critical that the exposed pad on
the backside of the LTC1733 package is soldered to the
board. Correctly soldered to a 2500mm
2
double-sided
1oz. copper board the LTC1733 has a thermal resistance
of approximately 40
°
C/W. Failure to make thermal contact
between the exposed pad on the backside of the package
and the copper board will result in thermal resistances far
greater than 40
°
C/W. As an example, a correctly soldered
LTC1733 can deliver over 1250mA to a battery from a 5V
supply at room temperature. Without a backside thermal
connection, this number could drop to less than 500mA.
V
CC
Bypass Capacitor
Many types of capacitors can be used for input bypassing.
However, caution must be exercised when using multi-
layer ceramic capacitors. Because of the self resonant and
high Q characteristics of some types of ceramic capaci-
tors, high voltage transients can be generated under some
start-up conditions, such as connecting the charger input
to a hot power source. For more information refer to
Application Note 88.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1734 | Lithium-Ion Linear Battery Charger in SOT-23(鋰離子線性電池充電器（SOT-23封裝）) |
| LTC1735IS | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1735C-1 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1735CS-1 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1735IS-1 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1733EMSE#PBF | 功能描述:IC CHRGR BATT MONO THERML 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC1733EMSE#PBF | 制造商:Linear Technology 功能描述:Battery Management IC |
| LTC1733EMSE#TR | 功能描述:IC CTRLR BATT CHRG LI-ION 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC1733EMSE#TRPBF | 功能描述:IC CHRGR BATT MONO THERML 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC1734ES6-4.1#TR | 功能描述:IC BATT CHRGR LI-ION LIN SOT23-6 RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。