- 您現在的位置：買賣IC網 > PDF目錄377763 > LTC1733 (Linear Technology Corporation) Monolithic Linear Lithium-Ion Battery Charger with Thermal Regulation PDF資料下載
參數資料
| 型號： | LTC1733 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Monolithic Linear Lithium-Ion Battery Charger with Thermal Regulation |
| 中文描述： | 單片線性鋰離子電池充電器與熱調節 |
| 文件頁數： | 9/16頁 |
| 文件大小： | 169K |
| 代理商： | LTC1733 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
LTC1733
9
sn1733 1733fs
Undervoltage Lockout (UVLO)
An internal undervoltage lockout circuit monitors the input
voltage and keeps the charger in shutdown mode until V
CC
rises above the undervoltage lockout threshold. The UVLO
circuit has a built-in hysteresis of 150mV. Furthermore, to
protect against reverse current in the power MOSFET, the
UVLO circuit keeps the charger in shutdown mode if V
CC
falls to within 30mV of the battery voltage. If the UVLO
comparator is tripped, the charger will not come out of
shutdown until V
CC
rises 60mV above the battery voltage.
Trickle Charge and Defective Battery Detection
At the beginning of a charge cycle, if the battery voltage is
low (below 2.48V) the charger goes into trickle charge
reducing the charge current to 10% of the full-scale
current. If the low battery voltage persists for one quarter
of the total charge time, the battery is assumed to be
defective, the charge cycle is terminated, the CHRG pin
output assumes a high impedance state, and the FAULT
pin latches low. The fault can be cleared by toggling V
CC
,
temporarily forcing the PROG pin above 2.15V, or tempo-
rarily forcing the BAT pin voltage above 2.48V.
Shutdown
The LTC1733 can be shutdown (I
CC
= 0.9mA) by pulling
the PROG pin above the 2.15V shutdown threshold volt-
age. In shutdown the internal linear regulator is turned off,
and the internal timer is reset.
Recharge
The LTC1733 has the ability to recharge a battery
assuming that the battery voltage has been charged above
4.05V (SEL = 5V) or 3.95V (SEL = 0V). Once above these
thresholds, a new charge cycle will begin if the battery
voltage drops below 4V (SEL = 5V) or 3.9V (SEL = 0V) due
to either a load on the battery or self-discharge. The
recharge circuit integrates the BAT pin voltage for a few
milliseconds to prevent a transient from restarting the
charge cycle.
If the battery voltage remains below 2.48V during trickle
charge for 1/4 of the programmed time, the battery may be
defective and the charge cycle will end. In addition, the
recharge comparator is disabled and a new charge cycle
will not begin unless the input voltage is toggled, the PROG
pin is pulled above the 2.15V shutdown threshold, or the
BAT pin is pulled above the 2.48V trickle charge threshold.
Programming Charge Current
The formula for the battery charge current (see Figure 1)
is:
I
CHG
= (I
PROG
) 1000
= (1.5V / R
PROG
) 1000 or
R
PROG
= 1500/I
CHG
where R
PROG
is the total resistance from the PROG pin to
ground. Under trickle charge conditions, this current is
reduced to 10% of the full-scale value.
For example, if 500mA charge current is required,
calculate:
R
PROG
= 1500/0.5A = 3k
For best stability over temperature and time, 1% metal-
film resistors are recommended.
If the charger is in constant-temperature or constant-
voltage mode, the battery current can be monitored by
measuring the PROG pin voltage as follows:
I
CHG
= (V
PROG
/ R
PROG
) 1000
Programming the Timer
The programmable timer is used to terminate the charge
cycle. The timer duration is programmed by an external
capacitor at the TIMER pin. The total charge time is:
Time (Hours) = (3 Hours) (C
TIMER
/ 0.1
μ
F) or
C
TIMER
= 0.1
μ
F Time (Hours)/3 (Hours)
The timer starts when an input voltage greater than the
undervoltage lockout threshold level is applied and the
program resistor is connected to ground. After a time-out
occurs, the charge current stops, and the CHRG output
assumes a high impedance state to indicate that the
charging has stopped. Connecting the TIMER pin to ground
disables the timer function.
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1733EMSE | Monolithic Linear Lithium-Ion Battery Charger with Thermal Regulation |
| LTC1734 | Lithium-Ion Linear Battery Charger in SOT-23(鋰離子線性電池充電器（SOT-23封裝）) |
| LTC1735IS | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1735C-1 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1735CS-1 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1733EMSE | 功能描述:IC CHRGR BATT MONO THERML 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC1733EMSE#PBF | 功能描述:IC CHRGR BATT MONO THERML 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC1733EMSE#PBF | 制造商:Linear Technology 功能描述:Battery Management IC |
| LTC1733EMSE#TR | 功能描述:IC CTRLR BATT CHRG LI-ION 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC1733EMSE#TRPBF | 功能描述:IC CHRGR BATT MONO THERML 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。