- 您現在的位置：買賣IC網 > PDF目錄377759 > LTC1644IGN (LINEAR TECHNOLOGY CORP) CompactPCI Bus Hot Swap Controller PDF資料下載
參數資料
| 型號： | LTC1644IGN |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | CompactPCI Bus Hot Swap Controller |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP-20 |
| 文件頁數： | 12/24頁 |
| 文件大?。?/td> | 452K |
| 代理商： | LTC1644IGN |
LTC1644
12
1644f
Power-Up Sequence
The LTC1644 is specifically designed for live insertion and
removal of CPCI boards. The typical application is shown
in Figure 1. The 3.3V, 5V, 12V and –12V inputs to the
LTC1644 come from the medium length power pins. The
long 5V and 3.3V connector pins are connected through
decoupling resistors to the medium length 5V and 3.3V
connector pins on the CPCI plug-in card and provide early
power for the LTC1644’s precharge circuit, pull-up resis-
tors and the PCI bridge chip. The BD_SEL# signal is
connected to the OFF/ON pin while the PWRGD pin is
connected to the HEALTHY# signal. The HEALTHY# signal
is combined with the PCI_RST# signal on-chip to generate
the LOCAL_PCI_RST# signal which is available at the
RESETOUT pin.
The power supplies are controlled by placing external
N-channel pass transistors in the 3.3V and 5V power paths
and internal pass transistors for the 12V and –12V power
paths (Figure 1).
Resistors R1 and R2 provide current fault detection and
R5 and C1 provide current control loop compensation.
Resistors R3 and R4 prevent high frequency oscillations
in Q1 and Q2. Shunt RC snubbers R15-C4 and R16-C5 and
zener diodes Z1 and Z2 prevent the 12V
IN
and V
EEIN
pins,
respectively, from ringing beyond the absolute maximum
rated supply voltages during hot insertion.
When the CPCI card is inserted, the long 5V and 3.3V
connector pins and GND pins make contact first. The
LTC1644’s precharge circuit biases the bus I/O pins to 1V
during this stage of the insertion (Figure 2). The 12V, –12V
and 5V and 3.3V medium length pins make contact during
the next stage of insertion. At this point the LTC1644
powers on but slot power is disabled as long as the OFF/ON
pin is pulled high by the 1.2k pull-up resistor to 5V
IN
.
During the final stage of board insertion, the BD_SEL#
short connector pin makes contact and the OFF/ON pin can
APPLICATIU
W
U
U
be pulled low. This enables the pass transistors to turn on
and a 21
μ
A current source is connected to TIMER (Pin4).
The current in each pass transistor increases until it
reaches the current limit for each supply. The 5V and 3.3V
supplies are then allowed to power up based on one of the
following rates:
Power-up rate:
(1)
dV
dt
A
C
or
I
C
or
I
C
LIMIT
V
LOAD VOUT
5
(
LIMIT
V
LOAD VOUT
3
(
=
μ
1
=
=
65
5
3
,
,
(
)
)
(
)
)
whichever is slower.
Current limit faults are ignored while the TIMER pin
voltage is ramping up and is less than 1V below 12V
IN
(Pin
1). Once all four supply voltages are within tolerance,
HEALTHY# (Pin 7) will pull low and LOCAL_PCI_RST# is
free to follow PCI_RST#.
Power-Down Sequence
When the BD_SEL# is pulled high, a power-down
sequence begins (Figure 3).
Internal switches are connected to each of the output
supply voltage pins to discharge the bypass capacitors to
ground. The TIMER pin is immediately pulled low. The
GATE pin (Pin 15) is pulled down by a 225
μ
A current
source to prevent the load currents on the 3.3V and 5V
supplies from going to zero instantaneously and glitching
the power supply voltages. When any of the output volt-
ages dips below its threshold, the HEALTHY# signal pulls
high and LOCAL_PCI_RST# will be asserted low.
Once the power-down sequence is complete, the CPCI
card may be removed from the slot. During extraction, the
precharge circuit will continue to bias the bus I/O pins at
1V until the 5V and 3.3V long connector pin connections
are broken.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1644 | CompactPCI Bus Hot Swap Controller |
| LTC1644CGN | 8-Bit, 40 MSPS ADC Single Ch., Internal S&H, Low Power 24-TSSOP -40 to 85 |
| LTC1647-3CGN | Dual Hot Swap Controllers |
| LTC1647-3IGN | Dual Hot Swap Controllers |
| LTC1647 | Low Power Timer 8-SO 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1644IGN#PBF | 功能描述:IC CONTROLLER HOT SWAP 20-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC1644IGN#TR | 功能描述:IC CONTROLLER HOT SWAP 20-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC1644IGN#TRPBF | 功能描述:IC CONTROLLER HOT SWAP 20-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC1645CS | 功能描述:IC CTRLR SEQ HOTSWAP DUAL 14SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1645CS#PBF | 功能描述:IC CTLR HOT SWAP SEQ DUAL 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。