參數資料
型號: LTC1643AL-1CGN#PBF
廠商: Linear Technology
文件頁數: 11/16頁
文件大?。?/td> 236K
描述: IC CTRLR HOTSWAP PCI BUS 16SSOP
標準包裝: 100
類型: 熱交換控制器
應用: CompactPCI?
內部開關:
電源電壓: 3.3V,5V,±12V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 16-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 16-SSOP
包裝: 管件
11
LTC1643AL
LTC1643AL-1/LTC1643AH
 1643afb
APPLICATIONS INFORMATION
U
U
U
Timer
During a power-up sequence, a 22礎 current source is
connected to the TIMER pin (Pin 4) and current limit faults
are ignored until the voltage ramps to within 0.9V of 12V
IN
(Pin 1). This feature allows the chip to power up a PCI slot
that can accept boards with widely varying capacitive
loads on the supplies. The power-up time will be:
t
C
V
I
I
ON
SUPPLY    SUPPLY
LIMIT   LOAD
E

2
"
For C
SUPPLY
 = 2000礔, V
SUPPLY
 = 5V, I
LIMIT
= 7A, I
LOAD
= 5A, the turn-on time will be ~10ms. The timer period
should be set longer than the maximum supply turn-on
time but short enough to not exceed the maximum safe
operating area of the pass transistor during a short circuit.
The timer period will be:
t
C
V
A
TIMER
TIMER
=
"   .
11 1
22?/DIV>
For C
TIMER
 = 0.1礔, the timer period will be ~50ms. The
TIMER pin (Pin 4) is immediately pulled low when ON
(Pin 5) goes low.
Thermal Shutdown
The internal switches for the 12V and 12V supplies are
protected by an internal current limit and thermal shut-
down circuit. When the temperature of chip reaches
150癈, all switches will be latched off and the FAULT pin
(Pin 6) will be pulled low.
Short-Circuit Protection
During a normal power-up sequence, if the TIMER (Pin 4)
is done ramping and a supply is still in current limit, all of
the pass transistors will be immediately turned off and the
FAULT pin (Pin 6) will be pulled low as shown in Figure 4.
If a short circuit occurs after the supplies are powered up,
the shorted supplys current will drop immediately to the
limit value (Figure 5).
If the supply remains in current limit for more than 14.6祍,
all of the supplies will be latched off. The 14.6祍 delay
prevents quick current spikesfor example, from a fan
turning onfrom causing false trips of the circuit breaker.
The chip will stay in the latched-off state until ON pin
(Pin 5) is cycled low then high, or the 12V
IN
 pin (Pin 1)
power supply is cycled.
To prevent excessive power dissipation in the pass tran-
sistors and to prevent voltage spikes on the supplies
during short-circuit conditions, the current limit on each
supply is designed to be a function of the output voltage.
As the output voltage drops, the current limit decreases.
Unlike a traditional circuit breaker function where huge
currents can flow before the breaker trips, the current
foldback feature assures that the supply current will be
kept at a safe level and prevent voltage glitches when
powering up into a short.
The current limit for the 5V and 3.3V supplies is set by
placing a sense resistor between 5V
IN
 (Pin 13) and 5V
SENSE
(Pin 12) and between 3V
IN
 (Pin 9) and 3V
SENSE
 (Pin 10).
The current limit will be set by:
I
LIMIT
 = 53mV/R
SENSE
For a 0.005& resistor, the current limit will be set at 10.6A
and fold back to 1.5A when the output is shorted. For a
0.007& resistor, the current limit will be set at 7.6A and
fold back to 1.1A when the output is shorted.
The current limit for the internal 12V switch is set at
850mA folding back to 250mA and the 12V switch at
450mA folding back to 160mA.
In systems where it is possible to exceed the current limit
for a short amount of time, it might be necessary to
prevent the analog current loop from responding quickly
so the output voltage does not droop. This can be accom-
plished by adding an RC filter across the sense resistor as
shown in Figure 6. R4 should be 20& or less to prevent
offset errors. A 0.1礔 capacitor gives a delay of about
1.5祍 and a 1礔 capacitor gives a delay of about 15祍.
CompactPCI Application
The LTC1643AL is designed for hot swapping CompactPCI
boards. The typical application is shown in Figure 7. The
3.3V, 5V, 12V and 12V inputs to the LTC1643AL come
from the medium length power pins. The long 3.3V, 5V and
V(I/O) pins power up the pull-up resistors, bus precharge
相關PDF資料
PDF描述
LTC1644CGN#TRPBF IC CONTROLLER HOT SWAP 20-SSOP
LTC1645IS#TRPBF IC CTRLR SEQ HOTSWAP DUAL 14SOIC
LTC1646IGN#TR IC CNTRLR HOTSWAP PCIDUAL 16SSOP
LTC1647-1IS8#TRPBF IC CONTROLLR HOTSWAP DUAL 8-SOIC
LTC1704EGN#TRPBF IC REG DL BUCK/LINEAR 16SSOP
相關代理商/技術參數
參數描述
LTC1643AL-1IGN 功能描述:IC CTRLR HOTSWAP PCI BUS 16SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型,PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V,12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP(12x12) 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC1643AL-1IGN#PBF 功能描述:IC CTRLR HOTSWAP PCI BUS 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型,PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V,12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP(12x12) 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC1643AL-1IGN#TR 功能描述:IC CTRLR HOTSWAP PCI BUS 16SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型,PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V,12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP(12x12) 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC1643AL-1IGN#TRPBF 功能描述:IC CTRLR HOTSWAP PCI BUS 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型,PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V,12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP(12x12) 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC1643AL-1IGNPBF 制造商:Linear Technology 功能描述:PCI-Bus Hot Swap Controller, LTC1643AL