- 您現在的位置：買賣IC網 > PDF目錄377757 > LTC1606AI (Linear Technology Corporation) 16-Bit, 250ksps, Single Supply ADC PDF資料下載
參數資料
| 型號： | LTC1606AI |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 16-Bit, 250ksps, Single Supply ADC |
| 中文描述： | 16位，250ksps的，單電源模數轉換器 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 169K |
| 代理商： | LTC1606AI |
7
LTC1606
Conversion Details
The LTC1606 uses a successive approximation algorithm
and an internal sample-and-hold circuit to convert an
analog signal to a 16-bit or two byte parallel output. The
ADC is complete with a precision reference and an internal
clock. The control logic provides easy interface to micro-
processors and DSPs. (Please refer to the Digital Interface
section for the data format.)
Conversion start is controlled by the CS and R/C inputs. At
the start of conversion the successive approximation
register (SAR) is reset. Once a conversion cycle has
begun, it cannot be restarted.
During the conversion, the internal 16-bit capacitive DAC
output is sequenced by the SAR from the most significant
bit (MSB) to the least significant bit (LSB). Referring to
Figure 1, V
IN
is connected through the resistor divider to
the sample-and-hold capacitor during the acquire phase
and the comparator offset is nulled by the autozero switches.
In this acquire phase, a minimum delay of 1.5
μ
s will
provide enough time for the sample-and-hold capacitor to
acquire the analog signal. During the convert phase, the
autozero switches open, putting the comparator into the
compare mode. The input switch switches C
SAMPLE
to
ground, injecting the analog input charge onto the sum-
ming junction. This input charge is successively com-
pared with the binary-weighted charges supplied by the
capacitive DAC. Bit decisions are made by the high speed
comparator. At the end of a conversion, the DAC output
balances the V
IN
input charge. The SAR contents (a 16-bit
data word) that represents the V
IN
are loaded into the
16-bit output latches.
Driving the Analog Inputs
The nominal input range for the LTC1606 is
±
10V or
(
±
4 V
REF
) and the input is overvoltage protected to
±
25V.
The input impedance is typically 10k
, therefore, it should
be driven with a low impedance source. Wideband noise
coupling into the input can be minimized by placing a
1000pF capacitor at the input as shown in Figure 2. An
NPO-type capacitor gives the lowest distortion. Place the
capacitor as close to the device input pin as possible. If an
amplifier is to be used to drive the input, care should be
taken to select an amplifier with adequate accuracy, linear-
ity and noise for the application. The following list is a
summary of the op amps that are suitable for driving the
LTC1606. More detailed information is available in the
Linear Technology data books and LinearView
TM
CD-ROM.
LT1007 - Low noise precision amplifier. 2.7mA supply
current
±
5V to
±
15V supplies. Gain bandwidth product
8MHz. DC applications.
LT1097 - Low cost, low power precision amplifier. 300
μ
A
supply current.
±
5V to
±
15V supplies. Gain bandwidth
product 0.7MHz. DC applications.
LT1227 - 140MHz video current feedback amplifier. 10mA
supply current.
±
5V to
±
15V supplies. Low noise and low
distortion.
LT1360 - 37MHz voltage feedback amplifier. 3.8mA sup-
ply current.
±
5V to
±
15V supplies. Good AC/DC specs.
LT1363 - 50MHz voltage feedback amplifier. 6.3mA sup-
ply current. Good AC/DC specs.
LT1364/LT1365 - Dual and quad 50MHz voltage feedback
amplifiers. 6.3mA supply current per amplifier. Good AC/
DC specs.
LT1468 - 90MHz 22V/
μ
s 16-bit accurate amplifier.
V
DAC
1606 F01
+
–
C
DAC
DAC
SAMPLE
HOLD
C
SAMPLE
S
A
R
16-BIT
LATCH
COMPARATOR
SAMPLE
SI
R
IN2
R
IN1
V
IN
APPLICATIO
S I
FOR
ATIO
U
W
U
U
Figure 1. LTC1606 Simplified Equivalent Circuit
1606 F02
1000pF
33.2k
V
IN
CAP
A
IN
200
Figure 2. Analog Input Filtering
LinearView is a trademark of Linear Technology Corporation
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1606AIG | 16-Bit, 250ksps, Single Supply ADC |
| LTC1606C | 16-Bit, 250ksps, Single Supply ADC |
| LTC1606CG | 16-Bit, 250ksps, Single Supply ADC |
| LTC1622CMS8 | 8-Bit, 40 kSPS ADC Serial Out, Low Power, Compatible to TLC540/545/1540, Single Ch. 8-SOIC |
| LTC1622 | Low Input Voltage Current Mode Step-Down DC/DC Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1606AIG | 功能描述:IC ADC 16BIT 5V SAMPLING 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1606AIG#PBF | 功能描述:IC A/D CONV 16BIT SAMPLNG 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1606AIG#TR | 功能描述:IC ADC 16BIT 5V SAMPLING 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1606AIG#TRPBF | 功能描述:IC A/D CONV 16BIT SAMPLNG 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| LTC1606AISW | 功能描述:IC ADC 16BIT 5V SAMPLING 28SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。