- 您現在的位置：買賣IC網 > PDF目錄377752 > LTC1539IGW (LINEAR TECHNOLOGY CORP) Dual High Efficiency, Low Noise, Synchronous Step-Down Switching Regulators PDF資料下載
參數資料
| 型號： | LTC1539IGW |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Dual High Efficiency, Low Noise, Synchronous Step-Down Switching Regulators |
| 中文描述： | 2 A SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO36 |
| 封裝： | 0.300 INCH, PLASTIC, SSOP-36 |
| 文件頁數： | 13/32頁 |
| 文件大?。?/td> | 451K |
| 代理商： | LTC1539IGW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
13
LTC 1538-AUX/LTC 1539
APPLICATIO
S I
FOR
ATIO
U
when the inductor current reaches zero while the bottom
MOSFET is on. Lower inductor values (higher
I
L
) will cause
this to occur at higher load currents, which can cause a dip
in efficiency in the upper range of low current operation. In
Burst Mode operation (TGS1, 2 pins open), lower inductance
values will cause the burst frequency to decrease.
W
U
U
The Figure 3 graph gives a range of recommended induc-
tor values vs operating frequency and V
OUT
.
Inductor Core Selection
Once the value for L is known, the type of inductor must be
selected. High efficiency converters generally cannot af-
ford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite, molypermalloy
or Kool M
μ
cores. Actual core loss is independent of core
size for a fixed inductor value, but it is very dependent on
inductance selected. As inductance increases, core losses
go down. Unfortunately, increased inductance requires more
turns of wire and therefore copper losses will increase.
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can con-
centrate on copper loss and preventing saturation. Ferrite
core material saturates “hard,” which means that induc-
tance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple.
Do
not allow the core to saturate!
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive than
ferrite. A reasonable compromise from the same manu-
facturer is Kool M
μ
. Toroids are very space efficient,
especially when you can use several layers of wire. Be-
cause they generally lack a bobbin, mounting is more
difficult. However, designs for surface mount are available
which do not increase the height significantly.
Power MOSFET and D1 Selection
Three external power MOSFETs must be selected for each
controller with the LTC1539: a pair of N-channel MOSFETs
for the top (main) switch and an N-channel MOSFET for
the bottom (synchronous) switch. Only one top MOSFET
is required for each LTC1538-AUX controller.
To take advantage of the Adaptive Power output stage, two
topside MOSFETs must be selected. A large [low R
SD(ON)
]
MOSFET and a small [higher R
DS(ON)
] MOSFET are re-
quired. The large MOSFET is used as the main switch and
works in conjunction with the synchronous switch. The
smaller MOSFET is only enabled under low load current
conditions. The benefit of this is to boost low to midcurrent
efficiencies while continuing to operate at constant fre-
quency. Also, by using the small MOSFET the circuit will
keep switching at a constant frequency down to lower
currents and delay skipping cycles.
The R
DS(ON)
recommended for the small MOSFET is
around 0.5
. Be careful not to use a MOSFET with an
R
DS(ON)
that is too low; remember, we want to conserve
gate charge. (A higher R
DS(ON)
MOSFET has a smaller gate
capacitance and thus requires less current to charge its
gate). For all LTC1538-AUX and cost sensitive LTC1539
applications, the small MOSFET is not required. The circuit
then begins Burst Mode operation as the load current
drops.
The peak-to-peak drive levels are set by the INTV
CC
volt-
age. This voltage is typically 5V during start-up (see
EXTV
CC
Pin Connection). Consequently, logic level thresh-
old MOSFETs must be used in most LTC1538-AUX/
LTC1539 applications. The only exception is applications
in which EXTV
CC
is powered from an external supply
greater than 8V (must be less than 10V), in which standard
threshold MOSFETs (V
GS(TH)
< 4V) may be used. Pay close
attention to the BV
DSS
specification for the MOSFETs as well;
many of the logic level MOSFETs are limited to 30V or less.
Selection criteria for the power MOSFETs include the "ON"
resistance R
SD(ON)
, reverse transfer capacitance C
RSS
,
input voltage and maximum output current. When the
LTC1538-AUX/LTC1539 are operating in continuous mode
the duty cycles for the top and bottom MOSFETs are given
by:
Main Switch Duty Cycle
Synchronous Switch Duty Cycle
=
=
(
)
V
V
V
V
V
OUT
IN
IN
OUT
IN
±
Kool M
μ
is a registered trademark of Magnetics, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1538-AUX | Advanced LinEPIC Self-Calibrating (Self-Cal) Precision Single Operational Amplifier 8-SOIC |
| LTC1539 | Dual High Efficiency, Low Noise, Synchronous Step-Down Switching Regulators |
| LTC1538-AUXIG | ER 1C 1#4 SKT PLUG |
| LTC1538IG-AUX | DIODE ZENER SINGLE 1000mW 15Vz 50mA-Izt 0.05 1uA-Ir 11 PowerDI-123 3K/REEL |
| LTC1538CG-AUX | Dual High Efficiency, Low Noise, Synchronous Step-Down Switching Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1539IGW#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1539IGW#TR | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1539IGW#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1540CDD | 功能描述:IC COMP NANOPOWER W/REF 8DFN RoHS:否 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 標準包裝:25 系列:- 類型:帶電壓基準 元件數:4 輸出類型:CMOS，開路漏極，TTL 電壓 - 電源，單路/雙路(±):2 V ~ 11 V，±1 V ~ 5.5 V 電壓 - 輸入偏移（最小值）:10mV @ 5V 電流 - 輸入偏壓（最小值）:- 電流 - 輸出（標準）:0.015mA @ 5V 電流 - 靜態（最大值）:8.5µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:12µs 磁滯:50mV 工作溫度:0°C ~ 70°C 封裝/外殼:16-DIP（0.300"，7.62mm） 安裝類型:通孔 包裝:管件 |
| LTC1540CDD#PBF | 功能描述:IC COMP NANOPOWER W/REF 8DFN RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 標準包裝:1 系列:- 類型:通用 元件數:1 輸出類型:CMOS，開路集電極，TTL 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電壓 - 輸入偏移（最小值）:7mV @ 5V 電流 - 輸入偏壓（最小值）:0.25µA @ 5V 電流 - 輸出（標準）:84mA @ 5V 電流 - 靜態（最大值）:120µA CMRR, PSRR（標準）:- 傳輸延遲（最大）:600ns 磁滯:- 工作溫度:-40°C ~ 85°C 封裝/外殼:SC-74A，SOT-753 安裝類型:表面貼裝 包裝:剪切帶 (CT) 產品目錄頁面:1268 (CN2011-ZH PDF) 其它名稱:*LMV331M5*LMV331M5/NOPBLMV331M5CT |
發布緊急采購，3分鐘左右您將得到回復。