- 您現在的位置：買賣IC網 > PDF目錄377751 > LTC1505 (Linear Technology Corporation) Constant-Current/Voltage High Efficiency Battery Charger(恒定電流/電壓,高效率電池電荷控制器) PDF資料下載
參數資料
| 型號： | LTC1505 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Constant-Current/Voltage High Efficiency Battery Charger(恒定電流/電壓,高效率電池電荷控制器) |
| 中文描述： | Constant-Current/Voltage高效電池充電器（恒定電流/電壓，高效率電池電荷控制器） |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 197K |
| 代理商： | LTC1505 |
7
LT1505
the noninverting input to the amplifier, VA in the Block
Diagram, that controls the charging current when the
device operates in constant voltage mode. The amplifier
VA controls the charging current to maintain the voltage
on the V
FB
pin at the reference voltage (2.465V). Input bias
current for VA is approximately 3nA. The LT1505 incorpo-
rates a resistor divider that can be used to select the
correct voltage for either three or four 4.1V or 4.2V
lithium-ion cells. For three cells the 3CELL pin is shorted
to the V
FB
pin. For four cells the 3CELL pin is not con-
nected. For 4.1V cells the 4.1V pin is connected to the V
FB
pin and the 4.2V pin is not connected. For 4.2V cells the
4.2V pin is connected to V
FB
and the 4.1V pin is not
connected. See the table below.
PRESET BATTERY VOLTAGE
12.3V (3
×
4.1V Cell)
16.4V (4
×
4.1V Cell)
12.6V (3
×
4.2V Cell)
16.8V (4
×
4.2V Cell)
PIN SELECTION
4.1V, V
FB
, 3CELL Short Together
4.1V, V
FB
, Short Together, 3CELL Floats
4.2V, V
FB
, 3CELL Short Together
4.2V, V
FB
, Short Together, 3CELL Floats
For battery voltages other than the preset values, an
external resistor divider can be used. If an external divider
is used then the 4.1V, 4.2V and 3CELL pins should not be
connected and BAT2 pin should be grounded. To maintain
the tight voltage tolerance, the external resistors should
have better than 0.25% tolerance. Note that the V
FB
pin will
float high and inhibit switching if it is left open.
V
C
(Pin 18):
This is the control signal of the inner loop of
the current mode PWM. Switching starts at 0.9V, higher
V
C
corresponds to higher charging current in normal
operation and reaches 1.1V at full charging current. A
capacitor of at least 0.33
μ
F to GND filters out noise and
controls the rate of soft start. Pulling this pin low will stop
switching. Typical output current is 60
μ
A.
PROG (Pin 19):
This pin is for programming the charge
current and for system loop compensation. During normal
operation, V
PROG
stays at 2.465V. If it is shorted to GND or
more than 1mA is drawn out of the pin, switching will stop.
When a microprocessor controlled DAC is used to pro-
gram charging current, it must be capable of sinking
current at a compliance up to 2.465V.
PI
FU
CTIO
N
S
U
U
BAT2 (Pin 20):
This pin is used to connect the battery to
the internal preset voltage setting resistor. An internal
switch disconnects the internal divider from the battery
when the device is in shutdown or when power is discon-
nected. This disconnect function eliminates the current
drain due to the resistor divider. This pin should be
connected to the positive node of the battery if the internal
preset divider is used. This pin should be grounded if an
external divider is used. Maximum input voltage on this
pin is 20V.
SENSE (Pin 21):
This pin is the noninverting input to the
current amplifier CA1 in the Block Diagram. Typical bias
current is –50
μ
A.
SPIN (Pin 22):
This pin is for the internal amplifier CA1
bias. It must be connected as shown in the application
circuit.
BAT (Pin 23):
Current Amplifier CA1 Inverting Input.
Typical bias current is –50
μ
A.
V
CC
(Pin 24):
Input Supply. For good bypass, a low ESR
capacitor of 10
μ
F or higher is required. Keep the lead
length to a minimum. V
CC
should be between 11V and 24V.
Do not force V
CC
below V
BAT
by more than 1V with the
battery present.
BOOSTC (Pin 25):
This pin is used to bootstrap and supply
the current sense amplifier CA1 for very low dropout
condition. V
CC
can be as low as only 0.4V above the battery
voltage. A diode and a capacitor are needed to get the
voltage from V
BOOST
. If low dropout is not needed and V
CC
is always 3V or higher than V
BAT
, this pin can be left
floating or tied to V
CC
. Do not force this pin to a voltage
lower than V
CC
. Typical input current is 1mA.
GBIAS (Pin 26):
This is the output of the internal 9.1V
regulator to power the drivers and control circuits. This pin
must be bypassed to a ground plane with a minimum of
2.2
μ
F ceramic capacitor. Switching will stop when V
GBIAS
drops below 7V.
BGATE (Pin 27):
Low Side Power MOSFET Drive.
PGND (Pin 28):
MOSFET Driver Power Ground. A solid
system ground plane is very important. See the LT1505
Demo Manual for further information.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1514-3.3 | Step-Up/Step-Down Switched Capacitor DC/DC Converters with Low-Battery Comparator(3.3V輸出,步升/步降開關電容DC/DC變換器（帶低電池比較器）) |
| LTC1514-5 | Step-Up/Step-Down Switched Capacitor DC/DC Converters with Low-Battery Comparator |
| LTC1514CS8-3.3 | Step-Up/Step-Down Switched Capacitor DC/DC Converters with Low-Battery Comparator |
| LTC1514CS8-5 | Step-Up/Step-Down Switched Capacitor DC/DC Converters with Low-Battery Comparator |
| LTC1514IS8-3.3 | Step-Up/Step-Down Switched Capacitor DC/DC Converters with Low-Battery Comparator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC150GY | 制造商:Thomas & Betts 功能描述:L.T. NON-MET CONDUIT 制造商:Thomas & Betts 功能描述:Hoses Flexible Grey |
| LTC150-TB | 制造商:Thomas & Betts 功能描述:TUBING, XTRAFLEX CONDUIT, BLACK, 1-1/2IN; External Diameter:1.9"; Conduit Color:Black; Series:LTC; Conduit Material:PVC; Accessory Type:1-1/2" Industrial Grade Liquidtight Conduit; Approval Bodies:UL; Body Material:PVC; Color:Black ;RoHS Compliant: Yes 制造商:Thomas & Betts 功能描述:Fittings Coupler 1.5inch Polyvinyl Chloride |
| LTC150TB-250 | 制造商:Thomas & Betts 功能描述:NON-METALLIC TYPE B CONDUIT 250 FT |
| LTC1514CS8-3.3 | 功能描述:IC REG MULTI CONFIG 3.3V 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LTC1514CS8-3.3#PBF | 功能描述:IC REG MULTI CONFIG 3.3V 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
發布緊急采購，3分鐘左右您將得到回復。