- 您現在的位置：買賣IC網 > PDF目錄377751 > LTC1503-1.8 (Linear Technology Corporation) High Efficiency Inductorless Step-Down DC/DC Converters PDF資料下載
參數資料
| 型號： | LTC1503-1.8 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | High Efficiency Inductorless Step-Down DC/DC Converters |
| 中文描述： | 高效率無電感降壓DC / DC轉換器 |
| 文件頁數： | 7/12頁 |
| 文件大小： | 187K |
| 代理商： | LTC1503-1.8 |
7
LTC1503-1.8/LTC1503-2
maintain regulation. This will only occur as V
IN
/V
OUT
nears
a 3-to-2 or 1-to-1 transition point. For example, under light
load conditions, the LTC1503-X can operate in 2-to-1
mode when V
IN
equals 4.1V with greater than 90% effi-
ciency. However, when the load is increased, the part can
no longer supply enough output current in 2-to-1 mode to
maintain regulation. This causes V
OUT
to droop below the
regulation point until COMP2 trips and forces the part to
skip from 2-to-1 mode to 3-to-2 mode. The COMP2
threshold is about 17mV (V
OUT
referred) below the main
comparator regulation point. Hysteresis in COMP2 will
force the part to transition in and out of mode skipping.
This will result in a slight V
OUT
decrease of approximately
20mV under mode skipping conditions.
Shutdown/Soft-Start Operation
The SHDN/SS pin is used to implement both low current
shutdown and soft-start. The soft-start feature limits
inrush currents when the regulator is initially powered up
or taken out of shutdown. Forcing a voltage lower than
0.35V (typ) will put the part into shutdown mode. Shut-
down mode disables all control circuitry and forces the
charge pump V
OUT
into a high impedance state. A 2
μ
A pull-
up current on the SHDN/SS pin will force the part into
active mode if the pin is left floating or is driven with an
open-drain output that is in a high impedance state. If the
pin is not driven with an open-drain device, it must be
forced to a logic high voltage of 2.2V (min) to ensure
proper V
OUT
regulation. The SHDN/SS pin should not be
driven to a voltage higher than V
IN
.
To implement soft-start, the SHDN/SS pin must be driven
with an open-drain device and a capacitor must be
connected from the SHDN/SS pin to GND. Once the open-
drain device is turned off, a 2
μ
A pull-up current will begin
charging the external SS capacitor and force the voltage
on the pin to ramp towards V
IN
. As soon as the SHDN
threshold is reached (0.35V typ), the internal reference
voltage which controls the V
OUT
regulation point will
follow the ramp voltage on the SHDN/SS pin (minus a
0.35V offset to account for the SHDN threshold) until the
reference reaches its final band gap voltage. This occurs
when the voltage on the SHDN/SS pin reaches
Figure 1b. Step-Down Charge Pump in 3-to-2 Mode
In 1-to-1 mode, switch S1 and S2 are connected in series
between V
IN
and V
OUT
as needed to boost V
OUT
back into
regulation (see Figure 1c). The REG ENABLE signal from
the main comparator (COMP1) controls switches S1 and
S2 directly. Since all of the V
OUT
current is sourced from
V
IN
, the efficiency in 1-to-1 mode is approximately equal
to that of a linear regulator.
Figure 1c. Step-Down Charge Pump in 1-to-1 Mode
Mode Selection and Mode Skipping
The optimal step-down conversion mode is chosen based
on V
IN
to V
OUT
differential voltage and output load condi-
tions. Two internal comparators are used to select the
default step-down mode based on the V
IN
and V
OUT
voltage. A separate comparator (COMP2) is used to sense
a droop on V
OUT
due to a heavy output load and force the
charge pump to skip to a higher output current mode to
S1
φ
1
S5
φ
2
S7
φ
2
S4
φ
2
S2
φ
1
C1
(EXTERNAL)
C1
–
C2
(EXTERNAL)
C1
+
C2
–
GND
C2
+
1503-1.8/2 F01b
V
IN
V
OUT
S3
φ
1
S6
φ
2
S2
S1
C1
(EXTERNAL)
C1
+
C1
–
1503-1.8/2 F01c
V
IN
V
OUT
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1503-2 | High Efficiency Inductorless Step-Down DC/DC Converters |
| LTC1503CMS8-1.8 | High Efficiency Inductorless Step-Down DC/DC Converters |
| LTC1503CMS8-2 | High Efficiency Inductorless Step-Down DC/DC Converters |
| LTC1503CS8-1.8 | Hex 2-Line To 1-Line Universal Multiplexers With 3-State Outputs 24-SOIC 0 to 70 |
| LTC1503CS8-2 | High Efficiency Inductorless Step-Down DC/DC Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1503CMS8-1.8 | 功能描述:IC REG BUCK SWITCHED CAP 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC1503CMS8-1.8#PBF | 功能描述:IC REG BUCK SWITCHED CAP 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC1503CMS8-1.8#PBF | 制造商:Linear Technology 功能描述:DC/DC Charge Pump Converter IC |
| LTC1503CMS8-1.8#TR | 功能描述:IC REG BUCK SWITCHED CAP 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC1503CMS8-1.8#TRPBF | 功能描述:IC REG BUCK SWITCHED CAP 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
發布緊急采購，3分鐘左右您將得到回復。