- 您現在的位置：買賣IC網 > PDF目錄377746 > LTC1411 (Linear Integrated Systems) Single Supply 14-Bit 2.5Msps ADC PDF資料下載
參數資料
| 型號： | LTC1411 |
| 廠商： | Linear Integrated Systems |
| 元件分類： | ADC |
| 英文描述： | Single Supply 14-Bit 2.5Msps ADC |
| 中文描述： | 單電源14位2.5Msps模數轉換器 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 230K |
| 代理商： | LTC1411 |
13
LTC1411
1411f
APPLICATIOU
An analog ground plane separate from the logic system
ground should be established under and around the ADC.
AGND1, 2, 3 (Pins 7 to 9), AVM (Pin 11), DGND (Pin 31)
and OGND (Pin 28) and all other analog grounds should
be connected to a single analog ground point. The REFOUT,
REFCOM1, REFCOM2 and AVP should bypass to this
analog ground plane (see Figure 10). No other digital
grounds should be connected to this analog ground
plane. Low impedance analog and digital power supply
common returns are essential to low noise operation of
the ADC and the foil width for these tracks should be as
wide as possible.
W
U
U
Timing and Control
Conversion start is controlled by the CONVST digital input.
The falling edge transition of the CONVST will start a
conversion. Once initiated, it cannot be restarted until the
conversion is complete. Converter status is indicated by
the BUSY output. BUSY is low during a conversion.
The digital output code is updated at the end of conversion
about 7ns after BUSY rises, i.e., output data is not valid on
the rising edge of BUSY. Valid data can be latched with the
falling edge of BUSY or with the rising edge of CONVST. In
either case, the data latched will be for the previous
conversion results. Figures 11a and 11b are the timing
diagrams for the LTC1411.
3V Input/Output Compatible
The LTC1411 operates on a 5V supply, which makes the
device easy to interface to 5V digital systems. This device
can also talk to 3V digital systems: the digital input pins
(CONVST, NAP and SLP) of the LTC1411 recognize 3V or
5V inputs. The LTC1411 has a dedicated output supply pin
(OV
DD
) that controls the output swings of the digital
output pins (D0 to D13, BUSY and OTR) and allows the
part to talk to either 3V or 5V digital systems. The output
is two’s complement binary.
Figure 12 is the input/output characteristics of the ADC
when A
IN–
= 2.5V. The code transitions occur midway
between successive integer LSB values (i.e., 0.5LSB,
1.5LSB, 2.5LSB... FS – 1.5LSB). The output code is scaled
such that 1LSB = FS/16384 = 3.6V/16384 = 219.7
μ
V.
Offset and Full-Scale Adjustment
In applications where absolute accuracy is important,
offset and full-scale errors can be adjusted to zero. Offset
error must be adjusted before full-scale error. Figure 13
shows the extra components required for full-scale error
adjustment. Zero offset is achieved by adjusting the
offset applied to the A
IN–
input. For zero offset error,
apply 2.49989V (i.e., –0.5LSB) at A
IN+
and adjust R2 at
the A
IN–
input until the output code flickers between 0000
0000 0000 00 and 1111 1111 1111 11. For full-scale
adjustment, an input voltage of 4.29967V (FS – 1.5LSBs)
is applied to A
IN+
and R5 is adjusted until the output code
flickers between 0111 1111 1111 10 and 0111 1111
1111 11.
Figure 10. Power Supply Grounding Practice
1411 F10
A
IN+
REFCOM2
OV
DD
DVP
AVP
LTC1411
DIGITAL
SYSTEM
ANALOG
INPUT
CIRCUITRY
REFCOM1
5
2
6
29
31
OGND
DGND
28
AVM
11
10
30
1
REFIN
4
REFOUT
3
A
IN–
AGND1
7
AGND2
8
+
AGND3
9
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1411CG | Single Supply 14-Bit 2.5Msps ADC |
| LTC1411IG | Single Supply 14-Bit 2.5Msps ADC |
| LTC1415IG | SINGLEMODE FIBER PATCH CABLE, PLENUM ST-LC 30M |
| LTC1415 | 12-Bit, 1.25Msps, 55mW Sampling A/D Converter |
| LTC1415C | 12-Bit, 1.25Msps, 55mW Sampling A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1411CG | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1411CG#PBF | 功能描述:IC ADC 14BIT 2.5MSPS 36SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1411CG#TR | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1411CG#TRPBF | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1411IG | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。