- 您現在的位置：買賣IC網 > PDF目錄10671 > LTC1403ACMSE-1#PBF (Linear Technology)IC ADC 14BIT 2.8MSPS 10-MSOP PDF資料下載
參數資料
| 型號： | LTC1403ACMSE-1#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 6/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT 2.8MSPS 10-MSOP |
| 標準包裝： | 50 |
| 位數： | 14 |
| 采樣率（每秒）： | 2.8M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 12mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 |
| 供應商設備封裝： | 10-MSOP 裸露焊盤 |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，單極；1 個差分，單極 |
| 產品目錄頁面： | 1346 (CN2011-ZH PDF) |
| 配用： | DC1082A-D-ND - BOARD SAR ADC LTC1403A DC1082A-C-ND - BOARD SAR ADC LTC1403A-1 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁
LTC1403-1/LTC1403A-1
14
14031fc
APPLICATIONS INFORMATION
Board Layout and Bypassing
Wire wrap boards are not recommended for high resolu-
tion and/or high speed A/D converters. To obtain the best
performance from the LTC1403-1/LTC1403A-1, a printed
circuit board with ground plane is required. Layout for
the printed circuit board should ensure that digital and
analog signal lines are separated as much as possible.
In particular, care should be taken not to run any digital
track alongside an analog signal track. If optimum phase
match between the inputs is desired, the length of the two
input wires should be kept matched.
High quality tantalum and ceramic bypass capacitors
should be used at the VDD and VREF pins as shown in the
Block Diagram on the first page of this data sheet. For op-
timum performance, a 10F surface mount AVX capacitor
with a 0.1F ceramic is recommended for the VDDandVREF
pins. Alternatively, 10F ceramic chip capacitors such as
Murata GRM219R60J106M may be used. The capacitors
mustbelocatedasclosetothepinsaspossible.Thetraces
connecting the pins and the bypass capacitors must be
kept short and should be made as wide as possible.
Figure7showstherecommendedsystemgroundconnec-
tions. All analog circuitry grounds should be terminated at
the LTC1403-1/LTC1403A-1 GND (Pins 4, 5, 6 and exposed
pad). The ground return from the LTC1403-1/LTC1403A-1
(Pins 4, 5, 6 and exposed pad) to the power supply
should be low impedance for noise free operation. Digital
circuitry grounds must be connected to the digital supply
common. In applications where the ADC data outputs and
control signals are connected to a continuously active
microprocessor bus, it is possible to get errors in the
conversion results. These errors are due to feedthrough
from the microprocessor to the successive approximation
comparator. The problem can be eliminated by forcing the
microprocessor into a Wait state during conversion or by
using three-state buffers to isolate the ADC data bus.
POWER-DOWN MODES
Upon power-up, the LTC1403-1/LTC1403A-1 is initialized
to the active state and is ready for conversion. The Nap
and Sleep mode waveforms show the power-down modes
for the LTC1403-1/LTC1403A-1. The SCK and CONV inputs
control the power-down modes (see Timing Diagrams).
Two rising edges at CONV, without any intervening ris-
ing edges at SCK, put the LTC1403-1/LTC1403A-1 in Nap
mode and the power drain drops from 14mW to 6mW.
The internal reference remains powered in Nap mode.
Figure 7. Recommended Layout
14031 F07
FREQUENCY (Hz)
MAGNITUDE
(dB)
–60
–30
–20
14031 F06b
–70
–80
–120
–100
0
–10
–40
–50
–90
–110
0
371k
185k
556k
741k
Figure 6b. LTC1403-1 6MHz Sine Wave 4096 Point FFT Plot
with the LT1819 Driving the Inputs Differentially
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B1R-MX-F3 | CONVERTER MOD DC/DC 7.5V 75W |
| VI-B1R-MX-F1 | CONVERTER MOD DC/DC 7.5V 75W |
| LTC1407ACMSE-1#PBF | IC ADC 14BIT 3MSPS 10-MSOP |
| LTC1403ACMSE#PBF | IC ADC 14BIT 2.8MSPS 10-MSOP |
| NCS2202SQ1T2G | IC COMPARATOR LV LP OD SC70-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1403ACMSEPBF | 制造商:Linear Technology 功能描述:ADC,LTC1403A 14bit 2.8MSPS SPI MSOP |
| LTC1403AHMSE | 制造商:Linear Technology 功能描述:ADC Single SAR 2.8Msps 14-bit Serial 10-Pin MSOP EP |
| LTC1403AHMSE#PBF | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1403AHMSE#TRPBF | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1403AIMSE | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。