- 您現在的位置：買賣IC網 > PDF目錄377739 > LTC1289BCN (LINEAR TECHNOLOGY CORP) Single Channel Codec-Bandwidth Independent of Sampling Rate 28-PLCC -40 to 85 PDF資料下載
參數資料
| 型號： | LTC1289BCN |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | Single Channel Codec-Bandwidth Independent of Sampling Rate 28-PLCC -40 to 85 |
| 中文描述： | 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP20 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-20 |
| 文件頁數： | 22/28頁 |
| 文件大小： | 487K |
| 代理商： | LTC1289BCN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁
22
LTC1289
U
S
A
O
PPLICATI
U
U
Figure 19 shows an FFT plot of the output spectrum for two
tones applied to the input of the A/D. Nonlinearities in the
A/D will cause distortion products at the sum and differ-
ence frequencies of the fundamentals and products of the
fundamentals. This is classically referred to as
intermodulation distortion (IMD).
8. Overvoltage Protection
Applying signals to the analog MUX that exceed the
positive or negative supply of the device will degrade the
accuracy of the A/D and possibly damage the device. For
example this condition would occur if a signal is applied to
the analog MUX before power is applied to the LTC1289.
Another example is the input source is operating from
different supplies of larger value than the LTC1289. These
conditions should be prevented either with proper supply
sequencing or by use of external circuitry to clamp or
current limit the input source. As shown in Figure 20, a
1k
resistor is enough to stand off
±
15V (15mA for one
only channel). If more than one channel exceeds the
supplies than the following guidelines can be used. Limit
the current to 7mA per channel and 28mA for all channels.
This means four channels can handle 7mA of input current
each. Reducing the ACLK and SCLK frequencies from the
maximum of 2MHz and 1MHz, respectively (see Typical
Peformance Characteristics curves Maximum ACLK Fre-
quency vs Source Resistance and Sample and Hold Acqui-
sition Time vs Source Resistance) allows the use of larger
current limiting resistors. Use 1N4148 diode clamps from
the MUX inputs to V
CC
and V
–
if the value of the series
resistor will not allow the maximum clock speeds to be
used or if an unknown source is used to drive the LTC1289
MUX inputs.
How the various power supplies to the LTC1289 are
applied can also lead to overvoltage conditions. For single
supply operation (i.e., unipolar mode), if V
CC
and REF
+
are
not tied together, then V
CC
should be turned on first, then
REF
+
. If this sequence cannot be met, connecting a diode
from REF
+
to V
CC
is recommended (see Figure 21).
For dual supplies (bipolar mode) placing two Schottky
diodes from V
CC
and V
–
to ground (Figure 22) will prevent
power supply reversal from occuring when an input source
is applied to the analog MUX before power is applied to the
device. Power supply reversal occurs, for example, if the
input is pulled below V
–
then V
CC
will pull a diode drop
below ground which could cause the device not to power
up properly. Likewise, if the input is pulled above V
CC
then
V
–
will be pulled a diode drop above ground. If no inputs
are present on the MUX, the Schottky diodes are not
required if V
–
is applied first, then V
CC
.
Because a unique input protection structure is used on the
digital input pins, the signal levels on these pins can
exceed the device V
CC
without damaging the device.
Figure 20. Overvoltage Protection for MUX
3.3V
22
μ
F
LTC1289 AIF21
REF
+
V
CC
LTC1289
1N4148
V
REF
14
20
Figure 21.
Figure 22. Power Supply Reversal
3.3V
22
μ
F
LTC1289 AIF20
DGND
V
–
AGND
V
CC
1k
LTC1289
CH0
V
IN
–3.3V
0.1
μ
F
3.3V
22
μ
F
LTC1289 AIF22
DGND
V
–
AGND
V
CC
LTC1289
–3.3V
0.1
μ
F
1N5817
1N5817
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1289BCS | Single Channel Codec-Bandwidth Independent of Sampling Rate 28-PLCC -40 to 85 |
| LTC1289BI | Single Channel Codec-Bandwidth Independent of Sampling Rate 64-LQFP -40 to 85 |
| LTC1289CC | Single Channel Codec W/Master-Slave Function (3 Slaves) and 89 dB SNR 28-SOIC |
| LTC1289CI | 3 Volt Single Chip 12-Bit Data Acquisition System |
| LTC1289BCJ | 3 Volt Single Chip 12-Bit Data Acquisition System |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1289BCN#PBF | 功能描述:IC DATA ACQ SYS 12BIT 3V 20-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| LTC1289BCSW | 功能描述:IC DATA ACQ SYS 12BIT 3V 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| LTC1289BCSW#PBF | 功能描述:IC DATA ACQ SYS 12BIT 3V 20-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| LTC1289BCSW#TR | 功能描述:IC DATA ACQ SYS 12BIT 3V 20SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| LTC1289BCSW#TRPBF | 功能描述:IC DATA ACQ SYS 12BIT 3V 20-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。