參數資料
型號： LTC1288CN8
廠商： LINEAR TECHNOLOGY CORP
元件分類： ADC
英文描述： 3V Micropower Sampling 12-Bit A/D Converters in SO-8 Packages
中文描述： 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP8
封裝： PLASTIC, DIP-8
文件頁數： 16/24頁
文件大?。?/td> 412K
代理商： LTC1288CN8
16
LTC1285/LTC1288
APPLICATIO
I
N
FOR
ATIO
U
Single-Ended Inputs
The sample-and-hold of the LTC1288 allows conversion
of rapidly varying signals. The input voltage is sampled
during the t
SMPL
time as shown in Figure 7. The sampling
interval begins as the bit preceding the MSBF bit is shifted
in and continues until the falling CLK edge after the MSBF
bit is received. On this falling edge, the S&H goes into hold
mode and the conversion begins.
W
U
Differential Inputs
With differential inputs, the ADC no longer converts just a
single voltage but rather the difference between two volt-
ages. In this case, the voltage on the selected “+” input is
still sampled and held and therefore may be rapidly time
varying just as in single-ended mode. However, the volt-
age on the selected “–” input must remain constant and be
free of noise and ripple throughout the conversion time.
Otherwise, the differencing operation may not be per-
formed accurately. The conversion time is 12 CLK cycles.
Therefore, a change in the “–” input voltage during this
interval can cause conversion errors. For a sinusoidal
voltage on the “–” input this error would be:
V
ERROR (MAX)
= V
PEAK
×
2
×
π
×
f(“–”)
×
12/f
CLK
Where f(“–”) is the frequency of the “–” input voltage,
V
PEAK
is its peak amplitude and f
CLK
is the frequency of the
CLK. In most cases V
ERROR
will not be significant. For a
60Hz signal on the “–” input to generate a 1/4LSB error
(152
μ
V) with the converter running at CLK = 120kHz, its
peak value would have to be 4.03mV.
ANALOG INPUTS
Because of the capacitive redistribution A/D conversion
techniques used, the analog inputs of the LTC1285/
LTC1288 have capacitive switching input current spikes.
These current spikes settle quickly and do not cause a
problem. However, if large source resistances are used or
if slow settling op amps drive the inputs, care must be
taken to insure that the transients caused by the current
spikes settle completely before the conversion begins.
“+” Input Settling
The input capacitor of the LTC1285 is switched onto “+”
input during the t
SMPL
time (see Figure 1) and samples
the input signal within that time. However, the input
capacitor of the LTC1288 is switched onto “+” input
during the sample phase (t
SMPL
, see Figure 7). The
sample phase is 1 1/2 CLK cycles before conversion
starts. The voltage on the “+” input must settle com-
pletely within t
SMPLE
for the LTC1285 and the LTC1288
respectively. Minimizing R
SOURCE+
and C1 will improve
the input settling time. If a large “+” input source resis-
tance must be used, the sample time can be increased by
using a slower CLK frequency.
“–” Input Settling
At the end of the t
SMPL
, the input capacitor switches to the
“–” input and conversion starts (see Figures 1 and 7).
During the conversion, the “+” input voltage is effectively
“held” by the sample-and-hold and will not affect the
conversion result. However, it is critical that the “–” input
voltage settles completely during the first CLK cycle of the
conversion time and be free of noise. Minimizing R
SOURCE–
and C2 will improve settling time. If a large “–” input
source resistance must be used, the time allowed for
settling can be extended by using a slower CLK frequency.
Input Op Amps
When driving the analog inputs with an op amp it is
important that the op amp settle within the allowed time
(see Figure 7). Again, the“+” and “–” input sampling times
can be extended as described above to accommodate
slower op amps. Most op amps, including the LT1006 and
LT1413 single supply op amps, can be made to settle well
even with the minimum settling windows of 12.5
μ
s (“+”
input) which occur at the maximum clock rate of 120kHz.
Source Resistance
The analog inputs of the LTC1285/LTC1288 look like a
20pF capacitor (C
IN
) in series with a 500
resistor (R
ON
)
as shown in Figure 8. C
IN
gets switched between the
相關PDF資料
PDF描述
LTC1285CN8 3V Micropower Sampling 12-Bit A/D Converters in SO-8 Packages
LTC1285CS8 3V Micropower Sampling 12-Bit A/D Converters in SO-8 Packages
LTC1288 Single Channel Codec-Bandwidth Independent of Sampling Rate 28-PLCC 0 to 70
LTC1288CS8 3V Micropower Sampling 12-Bit A/D Converters in SO-8 Packages
LTC1289BC 3 Volt Single Chip 12-Bit Data Acquisition System
相關代理商/技術參數
參數描述
LTC1288CN8#PBF 功能描述:IC A/D CONV SAMPLING 12BIT 8-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
LTC1288CN8PBF 制造商:Linear Technology 功能描述:LTC1288CN8PBF
LTC1288CS8 功能描述:IC A/D CONV SAMPLING 12BIT 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC1288CS8#PBF 功能描述:IC A/D CONV SAMPLING 12BIT 8SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC1288CS8#TR 功能描述:IC ADC 12BIT 3V SAMPLING 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*