- 您現在的位置：買賣IC網 > PDF目錄11024 > LTC1264CN (Linear Technology)IC FILTR BUILDNG BLK HISPD 24DIP PDF資料下載
參數資料
| 型號： | LTC1264CN |
| 廠商： | Linear Technology |
| 文件頁數： | 13/16頁 |
| 文件大小： | 0K |
| 描述： | IC FILTR BUILDNG BLK HISPD 24DIP |
| 標準包裝： | 15 |
| 濾波器類型： | 通用開關電容器 |
| 頻率 - 截止或中心： | 250kHz |
| 濾波器數： | 4 |
| 濾波器階數： | 2nd |
| 電源電壓： | ±2.37 V ~ 8 V |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 24-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 24-PDIP |
| 包裝： | 管件 |
6
LTC1264
1264fb
PI FU CTIO S
U
UU
CLK (Pin 18): Clock Input Pin. Any TTL or CMOS clock
source with a square wave output and 50% duty cycle
(
±10%) is an adequate clock source for the device. The
power supply for the clock source should not be the filter’s
power supply. The analog ground for the filter should be
connected to clock’s ground at a single point only. Table
1 shows the clock’s low and high level threshold values for
a dual or single supply operation.
Table 1. Clock Source High and Low Threshold Levels
POWER SUPPLY
HIGH LEVEL
LOW LEVEL
Dual Supply =
±7.5V
≥ 2.18V
≤ 0.5V
Dual Supply =
±5V
≥ 1.45V
≤ 0.5V
Dual Supply =
±2.5V
≥ 0.73V
≤ –2.0V
Single Supply = 12V
≥ 7.80V
≤ 6.5V
Single Supply = 5V
≥ 1.45V
≤ 0.5V
A pulse generator can be used as a clock source provided
the high level on-time is greater than 0.2
s.Sinewavesare
not recommended for clock input frequencies less than
100kHz, since excessively slow clock rise or fall times
generate internal clock jitter (maximum clock rise or fall
time
≤1s). The clock signal should be routed from the
right side of the IC package and perpendicular to it to avoid
coupling to any input or output analog signal path. A 200
resistor between clock source and Pin 11 will slow down
the rise and fall times of the clock to further reduce charge
coupling (Figures 1 and 2).
HPB/NB, BPB, LPB, LPA, BPA, HPA, HPD, BPD, LPD,
LPC, BPC, HPC/NC (Pins 2, 3, 4, 9, 10, 11, 14, 15, 16,
21, 22, 23): Output Pins. Each 2nd order section of the
LTC1264 has three outputs which typically source 3mA
and sink 1mA. Driving coaxial cables or resistive loads less
than 20k will degrade the total harmonic distortion perfor-
mance of any filter design. When evaluating the distortion
or noise performance of a particular filter design imple-
mented with an LTC1264, the final output of the filter
should be buffered with a wideband noninverting high
slew rate amplifier (Figure 3).
Figure 3. Wideband Buffer
–
+
LT1224
5k
1264 F03
INV B, INV A, INV D, INV C (Pins 1, 12, 13, 24): Inverting
Input Pins. These pins are the high impedance inverting
inputs of internal op amps and they are susceptible to stray
capacitive connections to low impedance signal outputs
and power supply lines.
SB, SA, SD, SC (Pins 5, 8, 17, 20): Summing Input Pins.
The summing pins connections determine the circuit
topology (mode) of each 2nd order section. Please refer to
Modes of Operation.
Please refer to the Maximum Frequency of Operation
paragraph under Applications Information for a guide to
the use of capacitor CC.
Mode 1b
Mode 1b is derived from Mode 1. In Mode 1b (Figure 5) two
additional resistors R5 and R6 are added to alternate the
amount of voltage fed back from the lowpass output into
the input of the SA (SB, SC or SD) switched-capacitor
summer. This allows the filter’s clock-to-center frequency
ratio to be adjusted beyond 20:1. Mode 1b maintains the
speed advantages of Mode 1 and should be considered an
ODES OF OPERATIO
W
U
For the definition of filter functions please refer to the
LTC1060 data sheet.
Mode 1
In Mode 1, the ratio of the external clock frequency to the
center frequency of each 2nd order section is internally
fixed at 20:1. Figure 4 illustrates Mode 1 providing 2nd
order notch, lowpass, and bandpass outputs. Mode 1 can
be used to make high order Butterworth lowpass filters; it
can also be used to make low Q notches and for cascading
2nd order bandpass functions tuned at the same center
frequency. Mode 1 is faster than Mode 3.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J51-IW-B1 | CONVERTER MOD DC/DC 12V 100W |
| MC9RS08KB8CWJ | MCU 8-BIT 8K FLASH 20-SOIC |
| MC9RS08KB8CTG | MCU 8-BIT 8K FLASH 16-TSSOP |
| MC9RS08KB12CTG | MCU 8-BIT 12K FLASH 16-TSSOP |
| VI-J4P-IW-B1 | CONVERTER MOD DC/DC 13.8V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1264CN#PBF | 功能描述:IC FILTR BUILDNG BLK HISPD 24DIP RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LTC1264CSW | 功能描述:IC FILTR BUILDNG BLK HISPD24SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LTC1264CSW#PBF | 功能描述:IC FILTR BUILDNG BLK HISPD24SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LTC1264CSW#TR | 功能描述:IC FILTER BUILD BLK QUAD 24-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LTC1264CSW#TRPBF | 功能描述:IC FILTER BUILD BLK QUAD 24-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。