LTC1164-5
1
11645fc
Low Power 8th Order
Pin Selectable Butterworth
or Bessel Lowpass Filter
Butterworth 20kHz Anti-Aliasing Filter
■
Pin Selectable Butterworth or Bessel Response
■ 4mA Supply Current with
±5V Supplies
■ fCUTOFF up to 20kHz
■
100
VRMS Wideband Noise
■ THD < 0.02% (50:1, VS = ±7.5V, VIN = 2VRMS)
■ Operates with a Single 5V Supply (1VRMS Input
Range)
■ 60
VRMS Clock Feedthrough (Single 5V Supply)
■ Operates up to
±8V Supplies
■
TTL/CMOS-Compatible Clock Input
■ No External Components
■ Available in 14-Pin DIP and 16-Pin SO Wide
Packages
The LTC
1164-5 is a monolithic 8th order filter; it approxi-
mates either a Butterworth or a Bessel lowpass response.
The LTC1164-5 features clock-tunable cutoff frequency
and low power consumption (4.5mA with
±5V supplies
and 2.5mA with single 5V supply).
Low power operation is achieved without compromising
noise or distortion performance. With
±5V supplies and
10kHz cutoff frequency, the operating signal-to-noise
ratio is 86dB and the THD throughout the passband is
0.015%. Under the same conditions, a 77dB signal-to-
noise ratio and distortion is obtained with a single 5V
supply while the clock feedthrough is kept below the noise
level. The maximum signal-to-noise ratio is 92dB.
The LTC1164-5 approximates an 8th order Butterworth
response with a clock-to-cutoff frequency ratio of 100:1
(Pin 10 to V
–) or 50:1 double-sampled (Pin 10 to V+ and
Pin 1 shorted to Pin 13). Double-sampling allows the input
signal frequency to reach the clock frequency before any
aliasing occurrence. An 8th order Bessel response can
also be approximated with a clock-to-cutoff frequency
ratio of 140:1 (Pin 10 to ground). With
±7.5V supply, ±5V
supply and single 5V supply, the maximum clock fre-
quency of the LTC1164-5 is 1.5MHz, 1MHz and 1MHz
respectively. The LTC1164-5 is pin-compatible with the
LTC1064-2 and LTC-1064-3.
Frequency Response
■ Anti-Aliasing Filters
■
Battery-Operated Instruments
■ Telecommunications Filters
■ Smoothing Filters
FEATURES
APPLICATIO S
U
DESCRIPTIO
U
TYPICAL APPLICATIO
U
, LTC and LT are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
FREQUENCY (kHz)
1
GAIN
(dB)
0
–10
–20
–30
–40
–50
–60
–70
–80
10
100
1164-5 TA02
1
2
3
4
5
6
7
14
13
12
11
10
9
8
LTC1164-5
VIN
8V
NC
–8V
CLK = 1MHz
TO V+
VOUT
WIDEBAND NOISE = 110
VRMS
THD IN PASSBAND < 0.02% AT VIN = 2VRMS
NOTE: THE CONNECTION FROM PIN 7 TO PIN 14
SHOULD BE MADE UNDER THE PACKAGE.
FOR 50:1 OPERATION CONNECT PIN 1 TO PIN 13
AS SHOWN. FOR 100:1 OR 150:1 OPERATION PINS 1
AND 13 SHOULD FLOAT. THE POWER SUPPLIES
SHOULD BE BYPASSED BY A 0.1
F CAPACITOR AS
CLOSE TO THE PACKAGE AS POSSIBLE.
1164-5 TA01