- 您現在的位置：買賣IC網 > PDF目錄9481 > LTC1093CSW#PBF (Linear Technology)IC DATA ACQ SYS 10BIT 6CH 16SOIC PDF資料下載
參數資料
| 型號： | LTC1093CSW#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 17/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DATA ACQ SYS 10BIT 6CH 16SOIC |
| 標準包裝： | 47 |
| 類型： | 數據采集系統（DAS），ADC |
| 分辨率（位）： | 10 b |
| 數據接口： | 串行 |
| 電壓電源： | 雙 ± |
| 電源電壓： | ±5V，4.5V，10V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
24
LTC1091/LTC1092
LTC1093/LTC1094
Figure 12. Reference Input Equivalent Circuit
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
Differential Inputs
With differential inputs, the A/D no longer converts just a
single voltage but rather the difference between two volt-
ages. In this case, the voltage on the selected “+” input is still
sampled and held and therefore may be rapidly time varying
just as in single-ended mode. However, the voltage on the
selected “–” input must remain constant and be free of noise
and ripple throughout the conversion time. Otherwise, the
differencing operation may not be performed accurately.
The conversion time is 10 CLK cycles. Therefore, a change
in the “–” input voltage during this interval can cause
conversion errors. For a sinusoidal voltage on the “–” input
this error would be:
VERROR(MAX) = (VPEAK)(2π) f(“–”)(10/fCLK)
Where f(“–”) is the frequency of the “–” input voltage,
VPEAK is its peak amplitude and fCLK is the frequency of the
CLK. In most cases VERROR will not be significant. For a
60Hz signal on the “–” input to generate a 0.25LSB error
(1.25mV) with the converter running at CLK = 500kHz, its
peak value would have to be 150mV.
5. Reference Inputs
The voltage between the reference inputs of the
LTC1091/LTC1092/LTC1093/LTC1094 defines the volt-
age span of the A/D converter. The reference inputs look
primarily like a 10k resistor but will have transient capaci-
tive switching currents due to the switched capacitor
conversion technique (see Figure 12). During each bit test
of the conversion (every CLK cycle), a capacitive current
spike will be generated on the reference pins by the A/D.
These current spikes settle quickly and do not cause a
problem. However, if slow settling circuitry is used to drive
the reference inputs, care must be taken to ensure that
transients caused by these current spikes settle com-
pletely during each bit test of the conversion.
When driving the reference inputs, three things should be
kept in mind:
1. The source resistance (ROUT) driving the reference
inputs should be low (less than 1
) to prevent DC
drops caused by the 1mA maximum reference current
(IREF).
2. Transients on the reference inputs caused by the
capacitive switching currents must settle completely
during each bit test (each CLK cycle). Figures 13 and
14 show examples of both adequate and poor settling.
Using a slower CLK will allow more time for the
reference to settle. However, even at the maximum
CLK rate of 500kHz most references and op amps can
be made to settle within the 2
s bit time.
3. It is recommended that the REF– input of the LTC1094
be tied directly to the analog ground plane. If REF– is
biased at a voltage other than ground, the voltage must
not change during a conversion cycle. This voltage
must also be free of noise and ripple with respect to
analog ground.
RON
5pF TO
30pF
10k
TYP
LTC1091/2/3/4
REF+
ROUT
VREF
EVERY CLK CYCLE
14
13
(AGND)
1091-4 F12
0.5mV/DIV
1
s/DIV
1091-4 F13
Figure 13. Adequate Reference Settling
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1093CSW | IC DATA ACQ SYS 10BIT 6CH 16SOIC |
| V24A5M300BF3 | CONVERTER MOD DC/DC 5V 300W |
| V24A5M300B | CONVERTER MOD DC/DC 5V 300W |
| LTC1296BCN | IC DATA ACQ SYSTEM 12BIT 20-DIP |
| V24A3V3M200B | CONVERTER MOD DC/DC 3.3V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1093MJ | 制造商:Linear Technology 功能描述:Single ADC SAR 26ksps 10-bit Serial 16-Pin CDIP |
| LTC1094 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1-, 2-, 6- and 8-Channel, 10-Bit Serial I/O Data Acquisition Systems |
| LTC1094AC | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1-, 2-, 6- and 8-Channel, 10-Bit Serial I/O Data Acquisition Systems |
| LTC1094ACN | 功能描述:IC DATA ACQ SYS 10BIT 8CH 20-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| LTC1094ACN#PBF | 功能描述:IC DATA ACQ SYS 10BIT 8CH 20-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。