- 您現在的位置：買賣IC網 > PDF目錄377727 > LT6600-10 (Linear Technology Corporation) Very Low Noise, Differential Amplifier and 10MHz Lowpass Filter PDF資料下載
參數資料
| 型號： | LT6600-10 |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 運動控制電子 |
| 英文描述： | Very Low Noise, Differential Amplifier and 10MHz Lowpass Filter |
| 中文描述： | 極低噪聲，差分放大器和10MHz低通濾波器 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 221K |
| 代理商： | LT6600-10 |
LT6600-10
9
6600f
APPLICATIU
W
U
U
The two amplifiers inside the LT6600-10 have indepen-
dent control of their output common mode voltage (see
the “block diagram” section). The following guidelines will
optimize the performance of the filter for single supply
operation.
Pin 7 must be bypassed to an AC ground with a 0.01
μ
F or
higher capacitor. Pin 7 can be driven from a low imped-
ance source, provided it remains at least 1.5V above V
–
and at least 1.5V below V
+
. An internal resistor divider sets
the voltage of Pin 7. While the internal 11k resistors are
well matched, their absolute value can vary by
±
20%. This
should be taken into consideration when connecting an
external resistor network to alter the voltage of Pin 7.
Pin 2 can be shorted to Pin 7 for simplicity. If a different
common mode output voltage is required, connect Pin 2
to a voltage source or resistor network. For 3V and 3.3V
supplies the voltage at Pin 2 must be less than or equal to
the mid supply level. For example, voltage (Pin 2)
≤
1.65V
on a single 3.3V supply. For power supply voltages higher
than 3.3V the voltage at Pin 2 can be set above mid supply.
The voltage on Pin 2 should not be more than 1V below the
voltage on Pin 7. The voltage on Pin 2 should not be more
than 2V above the voltage on PIn 7. Pin 2 is a high
impedance input.
The LT6600-10 was designed to process a variety of input
signals including signals centered around the mid-supply
voltage and signals that swing between ground and a
positive voltage in a single supply system (Figure 1). The
range of allowable input common mode voltage (the
average of V
IN+
and V
IN–
in Figure 1) is determined by
the power supply level and gain setting (see “Electrical
Characteristics”).
Common Mode DC Currents
In applications like Figure 1 and Figure 3 where the
LT6600-10 not only provides lowpass filtering but also
level shifts the common mode voltage of the input signal,
DC currents will be generated through the DC path be-
tween input and output terminals. Minimize these currents
to decrease power dissipation and distortion.
Consider the application in Figure 3. Pin 7 sets the output
common mode voltage of the 1st differential amplifier
inside the LT6600-10 (see the “Block Diagram” section) at
2.5V. Since the input common mode voltage is near 0V,
there will be approximately a total of 2.5V drop across the
series combination of the internal 402
feedback resistor
and the external 100
input resistor. The resulting 5mA
common mode DC current in each input path, must be
absorbed by the sources V
IN+
and V
IN–
. Pin 2 sets the
common mode output voltage of the 2nd differential
amplifier inside the LT6600-10, and therefore sets the
common mode output voltage of the filter. Since in the
example, Figure 3, Pin 2 differs from Pin 7 by 0.5V, an
additional 2.5mA (1.25mA per side) of DC current will flow
in the resistors coupling the 1st differential amplifier
output stage to filter output. Thus, a total of 12.5mA is
used to translate the common mode voltages.
A simple modification to Figure 3 will reduce the DC
common mode currents by 36%. If Pin 7 is shorted to
Pin 2 the common mode output voltage of both op amp
stages will be 2V and the resulting DC current will be 8mA.
Of course, by AC coupling the inputs of Figure 3, the
common mode DC current can be reduced to 2.5mA.
Noise
The noise performance of the LT6600-10 can be evaluated
with the circuit of Figure 7.
Given the low noise output of the LT6600-10 and the 6dB
attenuation of the transformer coupling network, it will be
necessary to measure the noise floor of the spectrum
analyzer and subtract the instrument noise from the filter
noise measurement.
Figure 6
1MHz INPUT LEVEL (V
P-P
)
0
20
0
–20
–40
–60
–80
–100
–120
3
5
6600
F06
1
2
4
6
O
3RD HARMONIC
85
°
C
1dB PASSBAND GAIN
COMPRESSION POINTS
1MHz 25
°
C
1MHz 85
°
C
3RD HARMONIC
25
°
C
2ND HARMONIC
25
°
C
2ND HARMONIC
85
°
C
相關PDF資料 |
PDF描述 |
|---|---|
| LT6600CS8-10 | Very Low Noise, Differential Amplifier and 10MHz Lowpass Filter |
| LT6600IS8-10 | Very Low Noise, Differential Amplifier and 10MHz Lowpass Filter |
| LT6600-20 | Very Low Noise, Differential Amplifier and 20MHz Lowpass Filter |
| LT6600CS8-20 | Very Low Noise, Differential Amplifier and 20MHz Lowpass Filter |
| LT6600IS8-20 | Very Low Noise, Differential Amplifier and 20MHz Lowpass Filter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT6600-15 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Very Low Noise, Differential Amplifi er and 15MHz Lowpass Filter |
| LT6600-2.5 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Very Low Noise, Differential Amplifi er and 2.5MHz Lowpass Filter |
| LT6600-2.5_09 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Very Low Noise, Differential Amplifi er and 2.5MHz Lowpass Filter |
| LT6600-20 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Very Low Noise, Differential Amplifier and 20MHz Lowpass Filter |
| LT6600-5 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Very Low Noise, Differential Amplifi er and 5MHz Lowpass Filter |
發布緊急采購，3分鐘左右您將得到回復。