- 您現在的位置：買賣IC網 > PDF目錄39399 > LT6350HMS8#TRPBF (LINEAR TECHNOLOGY CORP) 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO8 PDF資料下載
參數資料
| 型號： | LT6350HMS8#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO8 |
| 封裝： | LEAD FREE, PLASTIC, MSOP-8 |
| 文件頁數： | 14/28頁 |
| 文件大?。?/td> | 462K |
| 代理商： | LT6350HMS8#TRPBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LT6350
21
6350fb
APPLICATIONS INFORMATION
BOARD LAYOUT AND BYPASS CAPACITORS/DC1538A
DEMOBOARD
For single-supply applications it is recommended that
a high quality X5R or X7R, 0.1μF bypass capacitor be
placed directly between the V+ and the V– pin; the V– pin
(including the Exposed Pad on the DD8 package) should be
tied directly to a low impedance ground plane with minimal
routing. For split power supplies, it is recommended that
additional high quality X5R or X7R, 0.1μF capacitors
be used to bypass pin V+ to ground and V– to ground,
again with minimal routing. Small geometry (e.g., 0603)
surface mount ceramic capacitors have a much higher
self-resonant frequency than do leaded capacitors, and
perform best with the LT6350.
The +IN2 pin should be bypassed to ground with a high
quality ceramic capacitor of at least 0.1μF, both to reduce
the noise bandwidth of the recommended DC offset balance
resistor and to prevent changes in the common mode
reference voltage from being converted into a differential
output signal.
Stray parasitic capacitance at the –IN1 pin should be kept
to a minimum to prevent degraded stability resulting in
excessive ringing or oscillations. Traces at –IN1 should be
kept as short as possible, and any ground plane should
be stripped from under the pin and pin traces.
Because the outputs operate differentially, load imped-
ances seen by both outputs (stray or intended) should
be as balanced and symmetric as possible. This will help
preserve the balanced operation that minimizes the gen-
eration of even-order harmonic distortion in the output
stage and maximizes the rejection of common mode
signals and noise.
evaluation of the LT6350 following the above layout prac-
tices. Its schematic and component placement are shown
in Figures 9 and 10.
相關PDF資料 |
PDF描述 |
|---|---|
| LT6350IDD#PBF | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO8 |
| LT6350IMS8#TRPBF | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO8 |
| LT6350IDD#TRPBF | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO8 |
| LT6350CMS8#PBF | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO8 |
| LT6350IMS8#PBF | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT6350IDD#PBF | 功能描述:IC DIFF CONVERT/ADC DRIVER 8-DFN RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| LT6350IDD#TRPBF | 功能描述:IC DIFF CONVERT/ADC DRIVER 8-DFN RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| LT6350IDDPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Noise Single-Ended to Differential Converter/ADC Driver |
| LT6350IDDTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Noise Single-Ended to Differential Converter/ADC Driver |
| LT6350IMS8#PBF | 功能描述:IC DIFF CONVERT/ADC DRIVER 8MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。