- 您現在的位置：買賣IC網 > PDF目錄39400 > LT6350CDD#PBF (LINEAR TECHNOLOGY CORP) 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO8 PDF資料下載
參數資料
| 型號： | LT6350CDD#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO8 |
| 封裝： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-229WEED-1, DFN-8 |
| 文件頁數： | 9/28頁 |
| 文件大小： | 462K |
| 代理商： | LT6350CDD#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LT6350
17
6350fb
APPLICATIONS INFORMATION
The capacitance serves to provide the bulk of the charge
during the sampling process, while the two resistors at the
outputs of the LT6350 are used to dampen and attenuate
any charge injected by the ADC. The RC lter can also be
used to the additional benet of band limiting broadband
output noise. See the Noise Considerations section for
more information.
The selection of the RC time constant depends on the ADC;
but generally, longer time constants will improve SNR at
the expense of longer settling time. Excessive settling time
can introduce gain errors and can cause distortion if the
lter components are not perfectly linear. Note also that
too small of a resistor will not properly dampen the load
transient of the sampling process, prolonging the time
required for settling. 16-bit applications typically require
a minimum settling time of eleven RC time constants of
a rst order lter.
Note that the lter’s series resistance also serves to
decouple the LT6350 outputs from load capacitance. The
outputs of the LT6350 are designed to drive a maximum
of 40pF to ground or 20pF differentially; higher values
of lter capacitor should always be decoupled with lter
resistors of at least 25Ω.
High quality resistors and capacitors should be used in
the RC lter since these components can contribute to
distortion. For lowest distortion, choose capacitors with
a high quality dielectric, such as a C0G multilayer ceramic
capacitor. Metal lm surface mount resistors are more
linear than carbon types.
SETTING THE OUTPUT COMMON MODE VOLTAGE
The output common mode voltage is set by the voltage
applied to pin +IN2 in accordance with Equation (3). The
usable output common mode range is determined by the
input common mode range of the inverting op amp and
is from V– + 1.5V to V+.
In single supply applications, the optimal common mode
input range to the ADC is often determined by the ADC’s
reference. If the ADC has an output pin for setting the input
common mode voltage, it can be directly tied to the +IN2
pin, as long as it is capable of providing the input current
into +IN2 as listed in the Electrical Characteristics Table.
Alternatively, +IN2 may be driven by an external precision
reference such as the LT1790.
For lowest offset, the +IN2 pin should see 499Ω of driving
resistance in all applications (see Offset Considerations).
If the driving resistance is nominally less than 499Ω,
additional resistance can be added to make up the
difference. The resistor noise bandwidth can be reduced
by bypassing the +IN2 pin to the ground plane with a
chip ceramic capacitor of at least 0.1μF (see the Typical
Application on the front page). The bypass capacitance
also helps prevent AC signals on this pin from being
inadvertently converted to differential signals.
SHDN
If the SHDN pin (Pin 7), is pulled low within 300mV of the
negative supply rail, the LT6350 will power down. The pin
is connected through a diode to an internal current source
of 20μA. When pulled below the shutdown threshold, the
20μA current will ow from the pin. If the pin is left open
or pulled high (above V– + 2V), the part will enter normal
active operation, and the current into the pin will be very
small due to the reverse-biased diode.
相關PDF資料 |
PDF描述 |
|---|---|
| LT6604IUFF-15#TRPBF | SPECIALTY ANALOG CIRCUIT, PQCC34 |
| LT6604IUFF-15#PBF | SPECIALTY ANALOG CIRCUIT, PQCC34 |
| LTC1093AMJ | 6-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CDIP16 |
| LTC1093CJ | 6-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CDIP16 |
| LTC1094ACJ | 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT6350CDDTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Noise Single-Ended to Differential Converter/ADC Driver |
| LT6350CMS8#PBF | 功能描述:IC DRIVER DIFF CONVERT/ADC 8MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| LT6350CMS8#TRPBF | 功能描述:IC DIFF CONVERT/ADC DRIVER 8MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| LT6350CMS8PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Noise Single-Ended to Differential Converter/ADC Driver |
| LT6350CMS8TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Noise Single-Ended to Differential Converter/ADC Driver |
發布緊急采購，3分鐘左右您將得到回復。