9
623345fc
LT6233/LT6233-10
LT6234/LT6235
elecTrical characTerisTics The
l
denotes the specifications which apply over the –40°C < TA < 85°C
temperature range. VS = ±5V, VCM = VOUT = 0V, ENABLE = 0V, unless otherwise noted. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VOS
Input Offset Voltage
LT6233IS6, LT6233IS6-10
LT6234IS8, LT6235IGN
LT6234IDD
l
700
550
650
V
Input Offset Voltage Match
(Channel-to-Channel) (Note 6)
l
1000
V
VOS TC
Input Offset Voltage Drift (Note 10)
l
0.5
3
V/°C
IB
Input Bias Current
l
4
A
IB Match (Channel-to-Channel) (Note 6)
l
0.4
A
IOS
Input Offset Current
l
0.5
A
AVOL
Large-Signal Gain
VO = ±4.5V, RL = 10k
VO = ±4.5V, RL = 1k
l
68
20
V/mV
VCM
Input Voltage Range
Guaranteed by CMRR
l
–3
4
V
CMRR
Common Mode Rejection Ratio
VCM = –3V to 4V
l
90
dB
CMRR Match (Channel-to-Channel) (Note 6) VCM = –3V to 4V
l
84
dB
PSRR
Power Supply Rejection Ratio
VS = ±1.5V to ±5V
l
90
dB
PSRR Match (Channel-to-Channel) (Note 6) VS = ±1.5V to ±5V
l
84
dB
VOL
Output Voltage Swing Low (Note 8)
No Load
ISINK = 5mA
ISINK = 15mA
l
50
195
370
mV
VOH
Output Voltage Swing High (Note 8)
No Load
ISOURCE = 5mA
ISOURCE = 15mA
l
70
210
445
mV
ISC
Short-Circuit Current
l
±30
mA
IS
Supply Current per Amplifier
Disabled Supply Current per Amplifier
ENABLE = 4.8V
l
1
1.75
mA
A
IENABLE
ENABLE Pin Current
ENABLE = 0.3V
l
–110
A
VL
ENABLE Pin Input Voltage Low
l
0.3
V
VH
ENABLE Pin Input Voltage High
l
4.8
V
Output Leakage Current
ENABLE = 4.8V, VO = ±1V
l
1
A
tON
Turn-On Time
ENABLE = 5V to 0V, RL = 1k
l
900
ns
tOFF
Turn-Off Time
ENABLE = 0V to 5V, RL = 1k
l
160
s
SR
Slew Rate
AV = –1, RL = 1k, VO = –2V to 2V
l
10
V/s
LT6233-10, AV = –10, RL = 1k, VO = –2V to 2V l
95
V/s
FPBW
Full-Power Bandwidth (Note 9)
VOUT = 3VP-P; LT6233I, LT6234I, LT6235I
l
1.06
MHz
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Inputs are protected by back-to-back diodes. If the differential
input voltage exceeds 0.7V, the input current must be limited to less than
40mA.
Note 3: A heat sink may be required to keep the junction temperature
below the absolute maximum rating when the output is shorted
indefinitely.
Note 4: The LT6233C/LT6233I the LT6234C/LT6234I, and LT6235C/LT6235I
are guaranteed functional over the temperature range of –40°C to 85°C.
Note 5: The LT6233C/LT6234C/LT6235C are guaranteed to meet specified
performance from 0°C to 70°C. The LT6233C/LT6234C/LT6235C are
designed, characterized and expected to meet specified performance from
–40°C to 85°C, but are not tested or QA sampled at these temperatures.
The LT6233I/LT6234I/LT6235I are guaranteed to meet specified
performance from –40°C to 85°C.
Note 6: Matching parameters are the difference between the two amplifiers
A and D and between B and C of the LT6235; between the two amplifiers
of the LT6234. CMRR and PSRR match are defined as follows: CMRR and
PSRR are measured in V/V on the matched amplifiers. The difference is
calculated between the matching sides in V/V. The result is converted to
dB.