- 您現在的位置：買賣IC網 > PDF目錄377725 > LT6100IMS8 (LINEAR TECHNOLOGY CORP) Precision, Gain Selectable High Side Current Sense Amplifier PDF資料下載
參數資料
| 型號： | LT6100IMS8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Precision, Gain Selectable High Side Current Sense Amplifier |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 257K |
| 代理商： | LT6100IMS8 |
10
LT6100
6100f
The LT6100 high side current sense amplifier (Figure 1)
provides accurate unidirectional monitoring of current
through a user-selected sense resistor. The LT6100 fea-
tures a fully specified 4.1V to 48V input common mode
range. A high PSRR V
CC
supply (2.7V to 36V) powers the
current sense amplifier and the internal op amp circuitry.
The input sense voltage is level shifted from the positive
sense power supply to the ground reference and amplified
by a user-selected gain to the output. The buffered output
voltage is directly proportional to the current flowing
through the sense resistor.
Theory of Operation (Refer to Figure 1)
Current from the source at V
S+
flows through R
SENSE
to the
load at V
S–
, creating a sense voltage, V
SENSE
. Inputs V
S+
and V
S–
apply the sense voltage to R
G2
. The opposite ends
of resistors R
G1
and R
G2
are forced to be at equal poten-
tials by the voltage gain of amplifier A1. The current
through R
G2
is forced to flow through transistor Q1 and is
sourced to node V
O1
. The current from R
G2
flowing
through resistor R
O
gives a voltage gain of ten, V
O1
/V
SENSE
= R
O
/R
G2
= 10V/V. The sense amplifier output at V
O1
is
amplified again by amplifier A2. The inputs of amplifier A2
can operate to ground which ensures that small sense
voltage signals are detected. Amplifier A2 can be pro-
grammed to different gains via Pin 6 and Pin 7. Thus, the
total gain of the system becomes A
V
= 10 A2 and V
OUT
=
V
SENSE
A
V
.
Gain Setting
The LT6100 gain is set by strapping (or floating) the two
gain pins (see Table 1). This feature allows the user to
“zoom in” by increasing the gain for accurate measure-
ment of low currents.
A
V
= 10V/V G2, G2 is the gain of op amp A2.
Table 1. Gain Set with Pin 6 and Pin 7
A2 (PIN 6)
Open
V
EE
V
EE
Out
Open
V
EE
A4 (PIN 7)
Open
Out
Open
V
EE
V
EE
V
EE
G2
1
1.25
2
2.5
4
5
A
V
10
12.5
20
25
40
50
Selection of External Current Sense Resistor
External R
SENSE
resistor selection is a delicate trade-off
between power dissipation in the resistor and current
measurement accuracy. The maximum sense voltage may
be as large as
±
300mV to get maximum dynamic range.
For high current applications, the user may want to mini-
mize the sense voltage to minimize the power dissipation
in the sense resistor. The LT6100’s low input offset
voltage of 80
μ
V allows for high resolution of low sense
voltages. This allows limiting the maximum sense voltage
while still providing high resolution current monitoring.
Kelvin connection of the LT6100’s V
S+
and V
S–
inputs to
the sense resistor should be used to provide the highest
accuracy in high current applications. Solder connections
and PC board interconnect resistance (approximately
0.5m
per square) can be a large error in high current
systems. A 5A application might choose a 20m
sense
resistor to give a 100mV full-scale input to the LT6100.
Input offset voltage will limit resolution to 4mA. Neglect-
ing contact resistance at solder joints, even one square of
PC board copper at each resistor end will cause an error of
5%. This error will grow proportionately higher as moni-
tored current levels rise.
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LT6100HMS8 | CAP CERM 2200PF 10% 50V X7R 0805 |
| LT6100HDD | Precision, Gain Selectable High Side Current Sense Amplifier |
| LT6200 | 165MHz, Rail-to-Rail Input and Output, 0.95nV Low Noise, Op Amp Family |
| LT6200CS6-5 | 165MHz, Rail-to-Rail Input and Output, 0.95nV Low Noise, Op Amp Family |
| LT6201CS8 | 165MHz, Rail-to-Rail Input and Output, 0.95nV Low Noise, Op Amp Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT6100IMS8#PBF | 功能描述:IC AMP CURRENT SENSE 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| LT6100IMS8#TRPBF | 功能描述:IC AMP CURRENT SENSE 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| LT6100IMS8PBF | 制造商:Linear Technology 功能描述:Gain Selectable Current Sense Amp MSOP8 |
| LT6-100RED | 制造商:E-Z-Hook 功能描述:JUMPERS CONT 100LINKS PER CH RED |
| LT6-100-RED | 功能描述:JUMPERS CONT 100LINKS PER CH RED RoHS:否 類別:測試設備 >> 測試引線 - 跳線，專用型 系列:E-Z-LINK 標準包裝:1 系列:MG-B 配置:短頭鱷魚夾至短頭鱷魚夾 第一連接器:接線夾，微型，絕緣 第二連接器:接線夾，微型，絕緣 線纜長度:60.0"（1524.00mm） 所含物品:1 根引線，橙 材料 - 絕緣體:聚氯乙烯（PVC） 線規:18 AWG 電壓 - 額定:33VAC，70VDC 額定電流:5A 溫度范圍:122°F（50°C） 其它名稱:5995008270878 |
發布緊急采購，3分鐘左右您將得到回復。