- 您現在的位置：買賣IC網 > PDF目錄377724 > LT3781 (Linear Technology Corporation) DIODE, SCHOTTKY, 200MA, 30V, LOW LEAKAGE PDF資料下載
參數資料
| 型號： | LT3781 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | DIODE, SCHOTTKY, 200MA, 30V, LOW LEAKAGE |
| 中文描述： | 引導啟動雙晶體管同步前進控制器 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 267K |
| 代理商： | LT3781 |
11
LT3781
3781i
APPLICATIOU
Events that trigger a GFC are:
a) Exceeding the current limit of the 5V
REF
pin
b) Detecting an undervoltage condition on V
CC
c) Detecting an undervoltage condition on 5V
REF
d) Pulling the SHDN pin below the shutdown threshold
e) Exceeding the 1.25V fault detector threshold on
either the OVLO or THERM pins
OVLO and THERM pins is used to directly trigger a GFC. If
either of these pins are not used, they can be disabled by
connecting the pin to ground. The intention of the OVLO
pin is to allow the monitoring of the input supply to protect
from an overvoltage condition though the use of a resistor
divider from the input supply. Monitoring of system tem-
perature (THERM) is possible through use of a resistor
divider using a thermistor as a divider component. The
5V
REF
pin can provide the precision supply required for
these applications. When these fault detection circuits are
disabled during shutdown or V
CC
pin UVLO conditions, a
reduction in OVLO and THERM pin input impedance to
ground will occur. To prevent excessive pin input currents,
low impedance pull-up devices must not be used on these
pins.
W
U
U
Undervoltage Lockout
The LT3781 maintains a low current operational mode
when an undervoltage condition is detected on the V
CC
supply pin, or when V
CC
is below the undervoltage lockout
(UVLO) threshold. During a UVLO condition on the V
CC
pin, the LT3781 disables all internal functions with the
exception of the shutdown and UVLO circuitry. The exter-
nal 5V
REF
supply is also disabled during this condition.
Disabling of all switching control circuity reduces the
LT3781 supply current to <1mA, making for efficient
integration of trickle charging in systems that employ
output feedback supply generation.
The function of the high side switch output (TG) is also
gated by UVLO circuitry monitoring the bootstrap supply
(V
BST
– BSTREF). Switching of the TG pin is disabled until
the voltage across the bootstrap supply is greater than
7.4V. This helps prevent the possibility of forcing the high
side switch into a linear operational region, potentially
causing excessive power dissipation due to inadequate
gate drive during start-up.
Error Amplifer Configurations
The converter output voltage information is fed back to the
LT3781 onto the V
FB
pin where it is transformed into an
output current control voltage by the error amplifier. The
error amplifier is generally configured as an integrator and
is used to create the dominant pole for the main converter
feedback loop. The LT3781 error amplifier is a true high
gain voltage amplifier. The amplifier noninverting input is
internally referenced to 1.25V; the inverting input is the
V
FB
pin and the output is the V
C
pin. Because both low
frequency gain and integrator frequency characteristics
can be controlled with external components, this amplifier
allows far greater flexibility and precision compared with
use of a transconductance error amplifier.
In a nonisolated converter configuration where a resistor
divider is used to program the desired output voltage, the
error amplifier can be configured as a simple active
integrator, forming the system dominant pole ( Figure1).
Placing a capacitor C
ERR
from the V
FB
pin to the V
C
pin will
set the single-pole crossover frequency at (2
π
R
FB
C
ERR
)
-1
.
Additional poles and zeros can be added by increasing the
complexity of the RC network.
Figure 1. Nonisolated Error Amp Configuration
V
FB
R
FB
C
ERR
V
OUT
V
C
1.25V
3781 F01
LT3781
9
10
–
+
相關PDF資料 |
PDF描述 |
|---|---|
| LT3781EG | Bootstrap Start Dual Transistor Synchronous Forward Controller |
| LT3781IG | Bootstrap Start Dual Transistor Synchronous Forward Controller |
| LT4256-3 | Positive High Voltage Hot Swap Controller with Open-Circuit Detect |
| LT4256-3CGN | Positive High Voltage Hot Swap Controller with Open-Circuit Detect |
| LT4256-3IGN | Positive High Voltage Hot Swap Controller with Open-Circuit Detect |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3781_09 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:“Bootstrap” Start Dual Transistor Synchronous Forward Controller |
| LT3781EG | 功能描述:IC REG CTRLR ISO PWM CM 20-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LT3781EG#PBF | 功能描述:IC REG CTRLR ISO PWM CM 20-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,000 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:50% 電源電壓:9 V ~ 10 V 降壓:無 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 包裝:帶卷 (TR) |
| LT3781EG#TR | 功能描述:IC REG CTRLR ISO PWM CM 20-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LT3781EG#TRPBF | 功能描述:IC REG CTRLR ISO PWM CM 20-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
發布緊急采購，3分鐘左右您將得到回復。