參數資料
型號： LT3695EMSE-3.3#TRPBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： 2 A SWITCHING REGULATOR, 2420 kHz SWITCHING FREQ-MAX, PDSO16
封裝： LEAD FREE, PLASTIC, MSOP-16
文件頁數： 13/30頁
文件大?。?/td> 491K
代理商： LT3695EMSE-3.3#TRPBF
LT3695 Series
20
3695fa
This reduces the minimum input voltage to approximately
300mV above VOUT. At higher load currents, the inductor
current is continuous and the duty cycle is limited by the
maximum duty cycle of the LT3695 regulators, requiring
a higher input voltage to maintain regulation.
Soft-Start
The RUN/SS pin can be used to soft-start the LT3695
regulators, reducing the maximum input current during
start-up. The RUN/SS pin is driven through an external
RC network to create a voltage ramp at this pin. Figure 6
shows the start-up and shutdown waveforms with the
soft-start circuit. By choosing a large RC time constant,
the peak start-up current can be reduced to the current
that is required to regulate the output, with no overshoot.
Choose the value of the resistor so that it can supply 7.5μA
when the RUN/SS pin reaches 2.5V. For fault tolerant ap-
plications, see the discussion of the RUN/SS resistor in
the Fault Tolerance section.
Synchronization
To select low ripple Burst Mode operation, tie the SYNC
pin below 0.3V (this can be ground or a logic output).
Synchronizing the oscillator of the LT3695 regulators to
an external frequency can be done by connecting a square
wave (with 20% to 80% duty cycle) to the SYNC pin. The
square wave amplitude should have valleys that are below
0.3V and peaks that are above 0.8V (up to 6V).
The LT3695 regulators will not enter Burst Mode operation
at low output loads while synchronized to an external clock,
but instead will skip pulses to maintain regulation.
The maximum load current that the part can supply is
reduced when a clock signal is applied to SYNC.
The LT3695 regulators may be synchronized over a 300kHz
to 2.2MHz range. The RT resistor should be chosen to set
the LT3695 regulators switching frequency 20% below the
lowest synchronization input. For example, if the synchro-
nization signal is 360kHz, the RT should be chosen for
300kHz. To assure reliable and safe operation the LT3695
regulators will only synchronize when the output voltage is
near regulation as indicated by the PG ag. It is therefore
necessary to choose a large enough inductor value to
supply the required output current at the frequency set
by the RT resistor. See the Inductor Selection section for
more information. It is also important to note that slope
compensation is set by the RT value; to avoid subharmonic
oscillations, calculate the minimum inductor value using
the frequency determined by RT.
Shorted and Reversed Input Protection
If the inductor is chosen so that it will not saturate exces-
sively, the LT3695 regulators will tolerate a shorted output.
When operating in short-circuit condition, the LT3695
regulators will reduce their frequency until the valley cur-
rent is at a typical value of 1.6A (see Figure 7). There is
another situation to consider in systems where the output
will be held high when the input to the LT3695 regulators is
absent. This may occur in battery charging applications or
in battery backup systems where a battery or some other
supply is diode ORed with the LT3695 regulators’ output.
If the VIN pin is allowed to oat and the RUN/SS pin is held
high (either by a logic signal or because it is tied to VIN),
APPLICATIONS INFORMATION
5ms/DIV
VRUN/SS
5V/DIV
VOUT
5V/DIV
IL
1A/DIV
VRUN
5V/DIV
3695 F05
RUN
15k
0.22μF
RUN/SS
GND
Figure 6. To Soft-Start the LT3695 Regulators,
Add a Resistor and Capacitor to the RUN/SS Pin
3695 F07
IL
500mA/DIV
VSW
20V/DIV
0V
0A
2μs/DIV
Figure 7. The LT3695 Regulators Reduce Their Frequency
to Protect Against Shorted Output with 36V Input
相關PDF資料
PDF描述
LT3751IUFD#TR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20
LT3751IUFD#TRPBF 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20
LT3751EFE 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20
LT3751EUFD#TRPBF 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20
LT3751EUFD 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20
相關代理商/技術參數
參數描述
LT3695EMSE-5#PBF 功能描述:IC REG BUCK 5V 1A 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2
LT3695EMSE-5#PBF 制造商:Linear Technology 功能描述:IC STEP-DOWN REGULATOR MSOP-16
LT3695EMSE-5#TRPBF 功能描述:IC REG BUCK 5V 1A 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LT3695EMSEPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:1A Fault Tolerant Micropower Step-Down Regulator
LT3695EMSETRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:1A Fault Tolerant Micropower Step-Down Regulator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*