- 您現在的位置：買賣IC網 > PDF目錄30767 > LT3694IFE#PBF (LINEAR TECHNOLOGY CORP) 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO20 PDF資料下載
參數資料
| 型號： | LT3694IFE#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-20 |
| 文件頁數： | 4/28頁 |
| 文件大?。?/td> | 276K |
| 代理商： | LT3694IFE#PBF |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LT3694/LT3694-1
12
36941fa
APPLICATIONS INFORMATION
where f is the switching frequency of the LT3694 and L
is the value of the inductor. The peak inductor and switch
current is:
I
SWPK = ILPK = IOUT +
ΔI
L
2
To maintain output regulation, this peak current must be
less than the LT3694’s switch current limit, ILIM. ILIM is at
least 3.5A at low duty cycles (0.1) and decreases linearly
to 2.8A at DC = 0.8.
The minimum inductance can now be calculated as:
L
MIN =
1
DC
MIN
2 f
V
OUT + VF
I
LIM IOUT
However, it’s generally better to use an inductor larger
than the minimum value. The minimum inductor has large
ripple currents which increase core losses and require
large output capacitors to keep output voltage ripple low.
Select an inductor greater than LMIN that keeps the ripple
current below 30% of ILIM.
For input voltages greater than 30V, use an inductor with
a saturation current of 6A or greater and an inductance
value of 3.3μH or greater.
The inductor’s RMS current rating must be greater than the
maximum load current and its saturation current should
be greater than ILPK. For highest efficiency, the series
resistance (DCR) should be less than 0.1Ω. Table 2 lists
several vendors and types that are suitable.
Table 2. Inductors
SERIES
INDUCTANCE
RANGE (μH)
CURRENT
RANGE (A)
MANUFACTURER
WE-HC
1 to 6.5
6 to 15
Würth Elektronik
www.we-online.com
MSS1048
0.8 to 8
4 to 8
Coilcraft
www.coilcraft.com
CDRH103R
0.8 to 10
2.8 to 8.3
Sumida
www.sumida.com
VLF
2.2 to 10
3.8 to 7.7
TDK
www.component.tdk.
com
IHLP-2525CZ-11
1 to 10
2.5 to 9.5
Vishay
www.vishay.com
This analysis is valid for continuous mode operation
(IOUT > ILIM/2). For details of maximum output current in
discontinuous mode operation, see the Linear Technol-
ogy Application Note 44. Finally, for duty cycles greater
than 50% (VOUT/VIN > 0.5), a minimum inductance is
required to avoid subharmonic oscillations. This minimum
inductance is:
L
MIN =
(V
OUT + VF )
2A f
SW
with LMIN in μH and fSW in MHz. A detailed discussion
of subharmonic oscillations can be found in the Linear
Technology Application Note 19.
Input Capacitor Selection
Bypass the input of the LT3694 circuit with a ceramic
capacitor of X7R or X5R type. Y5V types have poor
performance over temperature and applied voltage, and
should not be used. A 4.7μF to 22μF ceramic capacitor
is adequate to bypass the LT3694 and will easily handle
the ripple current. Use a 22μF capacitor with fSW between
250kHz and 800kHz. Use a 10μF capacitor with fSW be-
tween 800kHz and 1.6MHz. Use a 4.7μF capacitor above
1.6MHz. Always check for sufficient margin by reducing
the capacitor value until the dropout increases by >500mV.
If the input power source has high impedance, or there
is significant inductance due to long wires or cables,
additional bulk capacitance may be necessary. This
can be provided with a lower performance electrolytic
capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT3694 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 10μF capacitor is capable of this task, but only if it is
placed close to the LT3694 and the catch diode (see the
PCB Layout section). A second precaution regarding the
ceramic input capacitor concerns the maximum input
voltage rating of the LT3694. A ceramic input capacitor
combined with trace or cable inductance forms a high
相關PDF資料 |
PDF描述 |
|---|---|
| LT3694-1IUFD#PBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3694IUFD#PBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3694-1IFE#PBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3694-1EFE#PBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3695IMSE-5#PBF | 2 A SWITCHING REGULATOR, 2420 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3694IUFD#PBF | 功能描述:IC REG TRPL BUCK/LINEAR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3694IUFD#TRPBF | 功能描述:IC REG TRPL BUCK/LINEAR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3694IUFD-1#PBF | 功能描述:IC REG TRPL BUCK/LINEAR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3694IUFD-1#TRPBF | 功能描述:IC REG TRPL BUCK/LINEAR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3694IUFDPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:36V, 2.6A Monolithic Buck Regulator With Dual LDO |
發布緊急采購，3分鐘左右您將得到回復。