- 您現在的位置：買賣IC網 > PDF目錄30767 > LT3641IUFD#PBF (LINEAR TECHNOLOGY CORP) 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28 PDF資料下載
參數資料
| 型號： | LT3641IUFD#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28 |
| 封裝： | 4 X 5 MM, LEAD FREE, PLASTIC, MO-220, QFN-28 |
| 文件頁數： | 14/28頁 |
| 文件大?。?/td> | 416K |
| 代理商： | LT3641IUFD#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LT3641
21
3641f
3641 F10
L2
L1
CIN2
CIN
CBST
COUT1
COUT2
Figure 9. Recommended PCB Layout, FE28 Package
APPLICATIONS INFORMATION
PCB Layout
For proper operation and minimum EMI, care must be
taken during the printed circuit board (PCB) layout. Figure 9
shows the recommended component placement with
trace, ground plane and via locations. The input loop
of the high voltage channel, which is formed by the VIN
and SW1 pins, the external catch diode (D1), the input
capacitor (CIN) and the ground, should be as small as
possible. These external components should be placed
on the same side of the circuit board as the LT3641, and
their connections should be made on that layer. Place a
local, unbroken ground plane below these components.
The BST and SW nodes should be as small as possible.
The boost capacitor (CBST) should be as close to the BST
and SW pins as possible.
The input loop of the low voltage channel is formed by
the VIN2 pin, the input capacitor (CIN2) and the ground.
Place CIN2 close to the VIN2 and the GND pin to minimize
this loop. Place a local, unbroken ground plane below
this input loop.
Keep the FB1 and FB2 nodes small so that the ground traces
will shield them from the switching nodes. The Exposed
Pad on the bottom of the package must be soldered to
the ground so that the pad acts as a heat sink. To keep
thermal resistance low, extend the ground plane as much as
possible, and add thermal vias under and near the LT3641
to additional ground planes within the circuit board and
on the bottom side.
Sequencing Options
In most LT3641 applications, the low voltage regulator
generating OUT2 will operate from the output of the
high voltage regulator generating OUT1. In this cascade
circuit, channel 1 must start before channel 2. However,
the LT3641 provides additional exibility in programming
the sequencing of the outputs. Figure 10 shows several
possibilities.
Figure 10a shows the easiest option. With EN2 tied to
FB1, channel 2 will start when OUT1 is within 10% of its
regulation point.
Figure 10b shows a simple alternative. By tying EN2 to
VIN2, channel 2 starts as soon as its input reaches its
minimum operating voltage of 2.3V.
Figure 10c shows a circuit that handles two other com-
mon requirements. If the system requires the low voltage
output to be in regulation before the higher voltage output
(for example core voltage must appear before the I/O sup-
ply), then add a PMOS switch and drive its gate with the
PGOOD2 pin, which will go low when both channels are
in regulation. This provides a third output OUT3, which is
present only when both OUT1 and OUT2 are in regulation.
Figure 10c also takes care of a potential problem in
cascaded power supply circuits. Because channel 2 is a
switching regulator, it appears as negative impedance load
to channel 1; as OUT1 decreases, the load required to sup-
ply the input of channel 2 increases. Since the channel 1
is current limited, you must be certain that it can supply
both its own load and the power required by channel 2. The
EN2 has an accurate threshold of 1.165V, and is used to
program an under-voltage lockout for channel 2, allowing
channel 1 to supply adequate power.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3653EDCB#TRPBF | 1.2 A BATTERY CHARGE CONTROLLER, 1650 kHz SWITCHING FREQ-MAX, PDSO8 |
| LT3684IMSE | 4 A SWITCHING REGULATOR, 3300 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT3684EDD#TR | 4 A SWITCHING REGULATOR, 3300 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT3694-1EUFD#PBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3694-1EUFD#TRPBF | 2.6 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3645 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:36V 500mA Step-Down Regulator and 200mA LDO |
| LT3645EMSE#PBF | 功能描述:IC REG DL BUCK/LINEAR 12-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3645EMSE#TRPBF | 功能描述:IC REG DL BUCK/LINEAR 12-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3645EMSEPBF | 制造商:Linear Technology 功能描述:36V 0.5A Sw. Regulator 0.2A LDO MSOP12EP |
| LT3645EUD#PBF | 功能描述:IC REG DL BUCK/LINEAR 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。