參數資料
型號： LT3513EUHF#PBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： 3.5 A SWITCHING REGULATOR, 2220 kHz SWITCHING FREQ-MAX, PQCC38
封裝： 5 X 7 MM, LEAD FREE, PLASTIC, MO-220WHKD, QFN-38
文件頁數： 22/22頁
文件大?。?/td> 374K
代理商： LT3513EUHF#PBF
LT3513
9
3513fc
VC2 (Pin 20): Control Voltage and Compensation Pin for
Internal Error Amplifier. Connect a series RC from this pin
to ground to compensate switching regulator 2.
VC4 (Pin 21): Control Voltage and Compensation Pin for
Internal Error Amplifier. Connect a series RC from this pin
to ground to compensate switching regulator 4.
RUN-SS1(Pin22):Run/Soft-StartPin.Thisisthesoft-start
pin for switching regulator 1. Place a soft-start capacitor
here to limit start-up inrush current and output voltage
ramp rate. When power is applied to the VIN pin, a 2A
current source charges the capacitor. When the voltage
at this pin reaches 0.8V, switch 1 turns on and begins
switching. For slower start-up use a larger capacitor. For
complete shutdown tie RUN-SS1 to ground.
NFB4 (Pin 23): Negative Feedback Pin. Tie the resistor di-
vidertaptothispinandsetVOFFaccordingtoVOFF=–1.18
(1 + R3/R4). Reference designators refer to Figure 2.
D4 (Pin 24): Internal Schottky Diode Pin. This pin is the
anode of an internal Schottky diode with the other end
connected to ground. This Schottky diode is used in
generating the VOFF output.
SW4(Pin25):SwitchNode.TheSW4pinisthecollectorof
theinternalNPNbipolartransistorforswitchingregulator4.
Minimize trace area at this pin to keep EMI down.
BD (Note 26): NPN LDO Base Drive. This pin controls the
base of the external NPN LDO transistor.
LDOPWR (Pin 27): Input Voltage for LDO Driver. This pin
supplies the current for the NPN LDO base. This pin can
be connected to VIN. To save power at high VIN voltages,
the pin can alternatively be connected to the AVDD supply.
BOOST (Pin 28): The BOOST pin is used to provide a
drive voltage higher than VIN to the switch 1 drive circuit.
An internal Schottky diode is connected between BIAS
and BOOST. A capacitor needs to be connected between
BOOST and SW1.
SENSE– (Pin 30) Negative Current Sense Input. This pin
(along with the SENSE+ pin) is used to sense the inductor
current for the buck switching regulator.
SENSE+ (Pin 31) Positive Current Sense Input. This pin
(along with the SENSE– pin) is used to sense the inductor
current for the buck switching regulator.
FB1 (Pin 32): Feedback Pin. Tie the resistor divider tap
to this pin and set VLOGIC according to VLOGIC = 1.235V
(1 + R1/R2). Reference designators refer to Figure 2.
SW1 (Pins 34, 35): Switch Node. The SW1 pins are the
emitter of the internal NPN bipolar power transistor for
switching regulator 1. These points must be tied together
for proper operation. Connect these pins to the inductor,
catch diode and boost capacitor.
VIN (Pins 36, 37): Input Voltage. This pin supplies current
to the internal circuitry of the LT3513. This pin must be
locally bypassed with a capacitor.
UVLO (Pin 38): Undervoltage Lockout. A resistor divider
connectedtoVINistiedtothispintoprogramtheminimum
input voltage at which the LT3513 will operate. This pin is
compared to the internal 1.25V reference. When UVLO is
less than 1.25V, the switching regulators are not allowed
to operate (the RUN/SS pins are still used to turn on each
switching regulator). When this pin falls below 1.25V,
3.9A will be pulled from the pin to provide programmable
hysteresis for UVLO.
Exposed Pad (Pin 39): Ground. The Exposed Pad of the
package provides both electrical contact to ground and
good thermal contact to the printed circuit board. The
Exposed Pad must be soldered to the circuit board for
proper operation.
pin FuncTions
相關PDF資料
PDF描述
LT3513IUHF#TRPBF 3.5 A SWITCHING REGULATOR, 2220 kHz SWITCHING FREQ-MAX, PQCC38
LT3573EMSE#TRPBF 1.85 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16
LT3573IMSE#PBF 1.85 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16
LT3573EMSE#PBF 1.85 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16
LT3573IMSE#TRPBF 1.85 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16
相關代理商/技術參數
參數描述
LT3513EUHF-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:2MHz High Current 5-Output Regulator for TFT-LCD Panels
LT3513IUHF#PBF 功能描述:IC REG 5-OUT FOR TFT-LCD 38QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
LT3513IUHF#TRPBF 功能描述:IC REG 5-OUT FOR TFT-LCD 38QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
LT3513IUHF-PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:2MHz High Current 5-Output Regulator for TFT-LCD Panels
LT3513IUHF-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:2MHz High Current 5-Output Regulator for TFT-LCD Panels
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*