參數資料
型號: LT3512MPMS#PBF
廠商: LINEAR TECHNOLOGY CORP
元件分類: 穩壓器
英文描述: 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12
封裝: LEAD FREE, PLASTIC, MSOP-16/12
文件頁數: 10/26頁
文件大?。?/td> 244K
代理商: LT3512MPMS#PBF
LT3512
18
3512fa
APPLICATIONS INFORMATION
Step 6: Design clamp circuit.
The clamp circuit protects the switch from leakage induc-
tance spike. A DZ clamp is the preferred clamp circuit. The
Zener and the diode need to be chosen.
The maximum Zener value is set according to the maxi-
mum VIN:
VZENER(MAX) ≤ 150V – VIN(MAX)
Example:
VZENER(MAX) ≤ 150V – 72V
VZENER(MAX) ≤ 78V
In addition, power loss in the clamp circuit is inversely
related to the clamp voltage as shown previously. Higher
clamp voltages lead to lower power loss.
A 68V Zener with a maximum of 72V will provide optimal
protection and minimize power loss. Half-watt Zeners will
satisfy most clamp applications involving the LT3512.
Power loss can be calculated using the equations presented
in the Leakage Inductance and Clamp Circuit section.
The Zener chosen is a 68V 0.5W Zener from On Semicon-
ductor (MMSZ5266BT1G).
Choose a diode that is fast and has sufficient reverse
voltage breakdown:
VREVERSE > VSW(MAX)
VSW(MAX) = VIN(MAX) + VZENER(MAX)
Example:
VREVERSE > 140V
The diode needs to handle the peak switch current of the
switch which was determined to be 0.45A. A 200V, 1.0A
diode from Diodes Inc. (DFLS1200) is chosen.
Step 7: Compensation.
Compensation will be optimized towards the end of the
design procedure. Connect a resistor and capacitor from
the VC node to ground. Use a 15k resistor and a 4.7nF
capacitor.
Step 8: Select RFB and RTC Resistors.
Use the following equations to choose starting values for
RFB and RTC. Set RREF to 10k.
R
FB =
V
OUT + VF + 0.55V
()N
PS RREF
1.2V
R
REF = 10k
R
TC =
R
FB
N
PS
Example:
R
FB =
15
+ 0.5+ 0.55V
()210k
1.2V
= 267k
R
TC =
267k
2
= 133k
Step 9: Adjust RFB based on output voltage.
Power up the application with application components
connected and measure the regulated output voltage.
Readjust RFB based on the measured output voltage.
R
FB(NEW ) =
V
OUT
V
OUT(MEAS)
R
FB(OLD)
Example:
R
FB(NEW ) =
15V
16.7V
267k
= 237k
Step 10: Remove RTC and measure output voltage
over temperature.
Measure output voltage in a controlled temperature envi-
ronment like an oven to determine the output temperature
coefficient. Measure output voltage at a consistent load
current and input voltage, across the temperature range
of operation. This procedure will optimize line and load
regulation over temperature.
Calculate the temperature coefficient of VOUT:
ΔV
OUT
ΔTemp
=
V
OUT(HOT) –VOUT(COLD)
T
HOT(
°C) –TCOLD(°C)
相關PDF資料
PDF描述
LT3512EMS#TRPBF 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12
LT3575IFE#PBF 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16
LT3575EFE#PBF 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16
LT3585EDDB-1#PBF 0.65 A BATTERY CHARGE CONTROLLER, PDSO10
LT3585EDDB-2#PBF 0.95 A BATTERY CHARGE CONTROLLER, PDSO10
相關代理商/技術參數
參數描述
LT3513 制造商:LINER 制造商全稱:Linear Technology 功能描述:2MHz High Current 5-Output Regulator for TFT-LCD Panels
LT3513EUHF#PBF 功能描述:IC REG 5-OUT FOR TFT-LCD 38QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器,Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN(7x7) 包裝:管件
LT3513EUHF#TRPBF 功能描述:IC REG 5-OUT FOR TFT-LCD 38QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器,Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN(7x7) 包裝:管件
LT3513EUHF-PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:2MHz High Current 5-Output Regulator for TFT-LCD Panels
LT3513EUHF-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:2MHz High Current 5-Output Regulator for TFT-LCD Panels