- 您現在的位置：買賣IC網 > PDF目錄30767 > LT3512EMS#PBF (LINEAR TECHNOLOGY CORP) 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12 PDF資料下載
參數資料
| 型號： | LT3512EMS#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12 |
| 封裝： | LEAD FREE, PLASTIC, MSOP-16/12 |
| 文件頁數： | 4/26頁 |
| 文件大?。?/td> | 244K |
| 代理商： | LT3512EMS#PBF |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
LT3512
12
3512fa
APPLICATIONS INFORMATION
Figure 5. Maximum Voltages for SW Pin Flyback Waveform
Figure 6. DZ Clamp
3512 F06
LS
D
Z
during that time, oscillation may occur at the output as
the current control loop will lose its ability to regulate. The
following equation based on maximum input voltage must
also be followed in selecting primary-side magnetizing
inductance:
LPRI ≥
tON(MIN) VIN(MAX)
IPEAK(MIN)
tON(MIN) = 100ns
IPEAK(MIN) = 100mA
Leakage Inductance and Clamp Circuits
Transformer leakage inductance (on either the primary or
secondary) causes a voltage spike to appear at the primary
after the output switch turns off. This spike is increasingly
prominent at higher load currents where more stored en-
ergy must be dissipated. When designing an application,
adequate margin should be kept for the effect of leakage
voltage spikes. In most cases the reflected output voltage
on the primary plus VIN should be kept below 100V. This
leaves at least 50V of margin for the leakage spike across
line and load conditions. A larger voltage margin will be
needed for poorly wound transformers or for excessive
leakage inductance. Figure 5 illustrates this point. Minimize
transformer leakage inductance.
A clamp circuit is recommended for most applications.
Two circuits that can protect the internal power switch
include the RCD (resistor-capacitor-diode) clamp and the
DZ (diode-Zener) clamp. The clamp circuits dissipate the
stored energy in the leakage inductance. The DZ clamp
is the recommended clamp for the LT3512. Simplicity of
design, high clamp voltages, and low power levels make the
DZ clamp the preferred solution. Additionally, a DZ clamp
ensures well defined and consistent clamping voltages.
Figure 5 shows the clamp effect on the switch waveform
and Figure 6 shows the connection of the DZ clamp.
Proper care must be taken when choosing both the diode
and the Zener diode. Schottky diodes are typically the best
choice, but some PN diodes can be used if they turn on
fast enough to limit the leakage inductance spike. Choose
a diode that has a reverse-voltage rating higher than the
maximum switch voltage. The Zener diode breakdown
voltage should be chosen to balance power loss and switch
<100V
<150V
VSW
VLEAKAGE
tOFF > 400ns
without Clamp
TIME
tSP < 150ns
<100V
<140V
<150V
VSW
tOFF > 400ns
with Clamp
TIME
tSP < 150ns
3512 F05
voltage protection. The best compromise is to choose the
largest voltage breakdown. Use the following equation to
make the proper choice:
VZENER(MAX) ≤ 150V – VIN(MAX)
For an application with a maximum input voltage of 72V,
choose a 68V VZENER which has VZENER(MAX) at 72V, which
will be below the 78V maximum.
The power loss in the clamp will determine the power rat-
ing of the Zener diode. Power loss in the clamp is highest
at maximum load and minimum input voltage. The switch
相關PDF資料 |
PDF描述 |
|---|---|
| LT3512HMS#TRPBF | 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12 |
| LT3512MPMS#PBF | 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12 |
| LT3512EMS#TRPBF | 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12 |
| LT3575IFE#PBF | 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3575EFE#PBF | 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3512HMS#PBF | 功能描述:IC REG FLYBK ISO ADJ .42A 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT3512HMS#TRPBF | 功能描述:IC REG FLYBK ISO ADJ .42A 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT3512HMSPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Monolithic High Voltage Isolated Flyback Converter |
| LT3512IMS#PBF | 功能描述:IC REG FLYBK ISO ADJ .42A 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3512IMS#TRPBF | 功能描述:IC REG FLYBK ISO ADJ .42A 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
發布緊急采購，3分鐘左右您將得到回復。