- 您現在的位置：買賣IC網 > PDF目錄30767 > LT3470IDDB#PBF (LINEAR TECHNOLOGY CORP) 0.2 A SWITCHING REGULATOR, PDSO8 PDF資料下載
參數資料
| 型號： | LT3470IDDB#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.2 A SWITCHING REGULATOR, PDSO8 |
| 封裝： | 3 X 2 MM, 0.75MM INCH HEIGHT, LEAD FREE, MO-229WECD-1, PLASTIC, DFN-8 |
| 文件頁數： | 5/20頁 |
| 文件大小： | 256K |
| 代理商： | LT3470IDDB#PBF |
13
LT3470
3470fc
SHDN
VIN
VOUT
(A)
(B)
VOUT
3470 F05
GND
SHDN
VIN
GND
C1
C2
VIAS TO FEEDBACK DIVIDER
VIAS TO LOCAL GROUND PLANE
OUTLINE OF LOCAL GROUND PLANE
PCB Layout
For proper operation and minimum EMI, care must be
taken during printed circuit board layout. Note that large,
switched currents flow in the power switch, the internal
catch diode and the input capacitor. The loop formed by
these components should be as small as possible. Fur-
thermore, the system ground should be tied to the regu-
lator ground in only one place; this prevents the switched
current from injecting noise into the system ground.
These components, along with the inductor and output
capacitor, should be placed on the same side of the circuit
board, and their connections should be made on that layer.
Place a local, unbroken ground plane below these compo-
nents, and tie this ground plane to system ground at one
Figure 5. A Good PCB Layout Ensures Proper, Low EMI Operation
APPLICATIO S I FOR ATIO
WU
UU
location, ideally at the ground terminal of the output
capacitor C2. Additionally, the SW and BOOST nodes
should be kept as small as possible. Unshielded inductors
can induce noise in the feedback path resulting in instabil-
ity and increased output ripple. To avoid this problem, use
vias to route the VOUT trace under the ground plane to the
feedback divider (as shown in Figure 5). Finally, keep the
FB node as small as possible so that the ground pin and
ground traces will shield it from the SW and BOOST nodes.
Figure 5 shows component placement with trace, ground
plane and via locations. Include vias near the GND pin, or
pad, of the LT3470 to help remove heat from the LT3470
to the ground plane.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3470ETS8#PBF | 0.2 A SWITCHING REGULATOR, PDSO8 |
| LT3470HDDB | 0.2 A SWITCHING REGULATOR, PDSO8 |
| LT3470ITS8#PBF | 0.2 A SWITCHING REGULATOR, PDSO8 |
| LT3470HTS8#TR | SWITCHING REGULATOR, PDSO8 |
| LT3495BEDDB#PBF | 0.78 A SWITCHING REGULATOR, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3470ITS8 | 制造商:LINEAR 制造商全稱:LINEAR 功能描述:Micropower Buck Regulator with Integrated Boost and Catch Diodes |
| LT3470ITS8#PBF | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 4V to 40V 8-Pin TSOT-23 制造商:Linear Technology 功能描述:IC BUCK REGULATOR 8-TSOT-23 制造商:Linear Technology 功能描述:SP-SWREG/Monolithic, Cut Tape 300mA, 40V Micropower Step-Down Reg in ThinSOT 制造商:Linear Technology 功能描述:IC, BUCK REGULATOR, 8-TSOT-23, Primary Input Voltage:40V, No. of Outputs:1, Output Voltage:16V, Output Current:200mA, No. of Pins:8, Operating Temperature Min:-40C, Operating Temperature Max:125C, MSL:MSL 1 - Unlimited , RoHS Compliant: Yes |
| LT3470ITS8#TR | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 4V to 40V 8-Pin TSOT-23 T/R 制造商:Linear Technology 功能描述:SP-SWREG/Monolithic, 300mA, 40V Micropower Step-Down Reg in ThinSOT |
| LT3470ITS8#TRM | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 4V to 40V 8-Pin TSOT-23 T/R |
| LT3470ITS8#TRMPBF | 功能描述:IC REG BUCK ADJ 0.2A TSOT23-8 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。