參數資料
型號： LT3470HTS8
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： SWITCHING REGULATOR, PDSO8
封裝： 1 MM HEIGHT, PLASTIC, MO-193, SOT-23, 8 PIN
文件頁數： 5/20頁
文件大?。?/td> 256K
代理商： LT3470HTS8
13
LT3470
3470fc
SHDN
VIN
VOUT
(A)
(B)
VOUT
3470 F05
GND
SHDN
VIN
GND
C1
C2
VIAS TO FEEDBACK DIVIDER
VIAS TO LOCAL GROUND PLANE
OUTLINE OF LOCAL GROUND PLANE
PCB Layout
For proper operation and minimum EMI, care must be
taken during printed circuit board layout. Note that large,
switched currents flow in the power switch, the internal
catch diode and the input capacitor. The loop formed by
these components should be as small as possible. Fur-
thermore, the system ground should be tied to the regu-
lator ground in only one place; this prevents the switched
current from injecting noise into the system ground.
These components, along with the inductor and output
capacitor, should be placed on the same side of the circuit
board, and their connections should be made on that layer.
Place a local, unbroken ground plane below these compo-
nents, and tie this ground plane to system ground at one
Figure 5. A Good PCB Layout Ensures Proper, Low EMI Operation
APPLICATIO S I FOR ATIO
WU
UU
location, ideally at the ground terminal of the output
capacitor C2. Additionally, the SW and BOOST nodes
should be kept as small as possible. Unshielded inductors
can induce noise in the feedback path resulting in instabil-
ity and increased output ripple. To avoid this problem, use
vias to route the VOUT trace under the ground plane to the
feedback divider (as shown in Figure 5). Finally, keep the
FB node as small as possible so that the ground pin and
ground traces will shield it from the SW and BOOST nodes.
Figure 5 shows component placement with trace, ground
plane and via locations. Include vias near the GND pin, or
pad, of the LT3470 to help remove heat from the LT3470
to the ground plane.
相關PDF資料
PDF描述
LT3470IDDB#PBF 0.2 A SWITCHING REGULATOR, PDSO8
LT3470ETS8#PBF 0.2 A SWITCHING REGULATOR, PDSO8
LT3470HDDB 0.2 A SWITCHING REGULATOR, PDSO8
LT3470ITS8#PBF 0.2 A SWITCHING REGULATOR, PDSO8
LT3470HTS8#TR SWITCHING REGULATOR, PDSO8
相關代理商/技術參數
參數描述
LT3470HTS8#PBF 制造商:Linear Technology 功能描述:SP-SWREG/Monolithic, Cut Tape 300mA, 40V MicroPower Step-Down Regulator with Int
LT3470HTS8#TRMPBF 功能描述:IC REG BUCK ADJ 0.2A TSOT23-8 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LT3470HTS8#TRPBF 功能描述:IC REG BUCK ADJ 0.2A TSOT23-8 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LT3470IDDB 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Buck Regulator with Integrated Boost and Catch Diodes
LT3470IDDB#PBF 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 4V to 40V 8-Pin DFN EP 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 4V to 40V 8-Pin DFN EP Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*