- 您現在的位置：買賣IC網 > PDF目錄44983 > LT3092IST#TR (LINEAR TECHNOLOGY CORP) SPECIALTY ANALOG CIRCUIT, PDSO3 PDF資料下載
參數資料
| 型號： | LT3092IST#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO3 |
| 封裝： | PLASTIC, SOT-223, 4 PIN |
| 文件頁數： | 22/22頁 |
| 文件大小： | 245K |
| 代理商： | LT3092IST#TR |
LT3092
9
3092fb
APPLICATIONS INFORMATION
inductive components and may be complex distributed
networks. In addition, the current source’s value will dif-
fer between applications and its connection may be GND
referenced, power supply referenced or oating in a signal
line path. Linear Technology strongly recommends that
stability be tested in situ for any LT3092 application.
In LT3092 applications with long wires or PCB traces, the
inductive reactance may cause instability. In some cases,
adding series resistance to the input and output lines (as
shown in Figure 2) may sufciently dampen these possible
high-Q lines and provide stability. The user must evaluate
the required resistor values against the design’s headroom
constraints. In general, operation at low output current
levels (< 5mA) automatically requires higher values of
programming resistors and may provide the necessary
damping without additional series impedance.
If the line impedances in series with the LT3092 are
complex enough such that series damping resistors are
not sufcient, a frequency compensation network may be
necessary. Several options may be considered.
From this point, selecting ROUT is easy, as it is a straight-
forward calculation from RSET. Take note, however, resistor
errors must be accounted for as well. While larger voltage
drops across RSET minimize the error due to offset, they
also increase the required operating headroom.
Obtaining the best temperature coefcient does not require
the use of expensive resistors with low ppm temperature
coefcients. Instead, since the output current of the LT3092
is determined by the ratio of RSET to ROUT, those resistors
should have matching temperature characteristics. Less
expensive resistors made from the same material will
provide matching temperature coefcients. See resistor
manufacturers’ data sheets for more details.
Stability and Frequency Compensation
The LT3092 does not require input or output capacitors
for stability in many current-source applications. Clean,
tight PCB layouts provide a low reactance, well controlled
operating environment for the LT3092 without requiring
capacitors to frequency-compensate the circuit. The front
page Typical Application circuit illustrates the simplicity
of using the LT3092.
Some current source applications will use a capacitor
connected in parallel with the SET pin resistor to lower
the current source’s noise. This capacitor also provides a
soft-start function for the current source. This capacitor
connection is depicted in Figure 7 (see the Quieting the
Noise section).
When operating with a capacitor across the SET pin resis-
tor, external compensation is usually required to maintain
stability and compensate for the introduced pole. The
following paragraphs discuss methods for stabilizing
the LT3092 for either this capacitance or other complex
impedances that may be presented to the device. Linear
Technology strongly recommends testing stability in situ
with nal components before beginning production.
Although the LT3092’s design strives to be stable without
any capacitors over a wide variety of operating conditions,
it is not possible to test for all possible combinations of
input and output impedances that the LT3092 will encounter.
These impedances may include resistive, capacitive and
Figure 2. Adding Series Resistor Decouples
and Dampens Long Line Reactances
IN
SET
OUT
+
–
LT3092
10μA
RSET
ROUT
RSERIES
LONG LINE
REACTANCE/INDUCTANCE
3092 F02
LONG LINE
REACTANCE/INDUCTANCE
相關PDF資料 |
PDF描述 |
|---|---|
| LT3092MPST#TRPBF | SPECIALTY ANALOG CIRCUIT, PDSO3 |
| LT3430IFE-1#TR | 6.5 A SWITCHING REGULATOR, 120 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3430EFE-1#TR | 6.5 A SWITCHING REGULATOR, 120 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3430IFE-1 | 6.5 A SWITCHING REGULATOR, 120 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3430EFE-1 | 6.5 A SWITCHING REGULATOR, 120 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3092ISTTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:200mA 2-Terminal Programmable Current Source |
| LT3092ITS8 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:200mA 2-Terminal Programmable Current Source |
| LT3092ITS8#PBF | 制造商:Linear Technology 功能描述:Adjustable Current Source 8-Pin TSOT-23 制造商:Linear Technology 功能描述:Bulk |
| LT3092ITS8#TRMPBF | 功能描述:IC PROG CURRENT SOURCE TSOT23-8 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩流/電流管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 功能:電流開關 檢測方法:- 精確度:±10% 輸入電壓:1.7 V ~ 5.5 V 電流 - 輸出:600mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-UFQFN 供應商設備封裝:10-UTQFN（1.4x1.8） 包裝:管件 |
| LT3092ITS8#TRPBF | 功能描述:IC PROG CURRENT SOURCE TSOT23-8 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩流/電流管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 功能:電流開關 檢測方法:- 精確度:±10% 輸入電壓:1.7 V ~ 5.5 V 電流 - 輸出:600mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-UFQFN 供應商設備封裝:10-UTQFN（1.4x1.8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。