- 您現在的位置：買賣IC網 > PDF目錄377720 > LT1990 (Linear Technology Corporation) 250V Input Range G = 1, 10, Micropower, Difference Amplifier PDF資料下載
參數資料
| 型號： | LT1990 |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 運動控制電子 |
| 英文描述： | 250V Input Range G = 1, 10, Micropower, Difference Amplifier |
| 中文描述： | 250V輸入范圍增益\u003d 1，10，微功耗，差分放大器 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 222K |
| 代理商： | LT1990 |
LT1990
13
1990f
APPLICATIOU
W
U
U
impedance source. Also the source impedance of a signal
connected to the REF pin must be on the order of a few
ohms or less to preserve the high accuracy of the LT1990.
While the LT1990 comes from the factory with an excellent
CMRR, some precision applications with a large applied
common mode voltage may require a method to trim out
residual common mode error. This is easily accomplished
by adding series resistance to each input, +IN and –IN,
such that an adjustable resistance difference of
±
1k
is
provided. This is most easily realized by adding a fixed
1k
in series with one of the inputs, and a 2k
trimmer in
series with the other as shown in Figure 1. The trim range
of this configuration is
±
0.1% for the internal gain resistor
matching, so a much more finely resolved correction is
available using the LT1990 than is realizable with ordinary
discrete solutions. In applications where the input
common mode voltage is relatively constant and large
(perhaps at or beyond the supply range), this same
configuration can be treated as an offset adjustment.
–
+
LT1990
1k
2k
Figure 1. Optional CMRR Trim
Dual Differential-Input Arithmetic Block
The internal resistor network topology of the LT1990
allows the GAIN1 and GAIN2 pins to be used as another
differential input in addition to the normal +IN and –IN
port. This can be a very useful function for implementing
servo-loop differential error amplifiers, for example. In
this mode of operation, the output is governed by the
following relationship:
V
O
= 10 (V
+IN
– V
–IN
+ V
GAIN2
– V
GAIN1
) + V
REF
Unlike the main inputs, the GAIN1 and GAIN2 pins are
clamped by substrate diodes and ESD structures, thus the
operating voltage range of these pins is limited to V
–
– 0.2V
to V
–
+ 36V. If the GAIN inputs are brought beyond the
operating input range, care must be taken to limit the input
currents to less than 10mA to prevent damage to the
device. Also, since the gain setting resistors associated
with the GAIN1 and GAIN2 inputs are in the 10k
area, low
source impedances are particularly important to preserve
the precision of the LT1990.
This dual differential input mode of operation is used in the
circuit as shown in Figure 2.
This circuit is a high efficiency H-bridge driver that is PWM
modulated to provide a controlled current to an electro-
magnet coil. Since the common mode voltage of the
current sense resistor R
S
varies with operating current
and the coil properties, a differential feedback is required.
In this application, it was desirable to allow the control
input to utilize the wide common mode range port (+IN and
–IN) so that constraints on input referencing are elimi-
nated. The GAIN1 and GAIN2 pins always operate within
the supply range and both ports operate with a gain of 10
to develop the loop error. The LTC1923 provides the loop
integrator and PWM functions of the servo.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1990ACS8 | 250V Input Range G = 1, 10, Micropower, Difference Amplifier |
| LT1990AIS8 | 250V Input Range G = 1, 10, Micropower, Difference Amplifier |
| LT1990CS8 | 250V Input Range G = 1, 10, Micropower, Difference Amplifier |
| LT1990IS8 | 250V Input Range G = 1, 10, Micropower, Difference Amplifier |
| LT1991ACMS | Precision, 100UA Gain Selectable Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1990ACS8 | 功能描述:IC AMP DIFF +/-250V MCRPWR 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| LT1990ACS8#PBF | 功能描述:IC AMP DIFF +/-250V MCRPWR 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| LT1990ACS8#TR | 功能描述:IC AMP DIFF +/-250V MCRPWR 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| LT1990ACS8#TRPBF | 功能描述:IC AMP DIFF +/-250V MCRPWR 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| LT1990AHS8 | 制造商:Linear Technology 功能描述:SP Amp DIFF AMP Single R-R O/P ±18V/36V 8-Pin SOIC N 制造商:Linear Technology 功能描述:SP Amp DIFF AMP Single R-R O/P 18V/36V 8-Pin SOIC N |
發布緊急采購，3分鐘左右您將得到回復。