參數資料
型號： LT1952MPGN-1#TRPBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO16
封裝： 0.150 INCH, LEAD FREE, PLASTIC, SSOP-16
文件頁數： 8/28頁
文件大?。?/td> 357K
代理商： LT1952MPGN-1#TRPBF
LT1952/LT1952-1
16
19521fe
Programming Synchronous Rectifier Timing:
SOUT to OUT delay (‘tDELAY’)
The LT1952/LT1952-1 have an additional output SOUT
which provides a
±50mA peak drive clamped to 12V. In
applications requiring synchronous rectification for high
efficiency, the LT1952/LT1952-1 SOUT provides a sync
signal for secondary side control of the synchronous
rectifier MOSFETs (Figure 11). Timing delays through the
converter can cause non-optimum control timing for the
synchronous rectifier MOSFETs. The LT1952/LT1952-1
provide a programmable delay (tDELAY, Figure 8) between
SOUT rising edge and OUT rising edge to optimize timing
control for the synchronous rectifier MOSFETs to achieve
maximum efficiency gains. A resistor RDELAY connected
from the DELAY pin to ground sets the value of tDELAY.
Typical values for tDELAY range from 10ns with RDELAY =
10k to 160ns with RDELAY = 160k. (see graph in Typical
Performance Characteristics)
APPLICATIONS INFORMATION
SS_MAXDC pin using a resistor divider from VREF. An
increase of voltage at the SS_MAXDC pin causes the
maximum duty cycle clamp to increase.
To program the volt-second clamp, the following steps
should be taken:
(1)The maximum operational duty cycle of the converter
should be calculated for the given application.
(2)An initial value for the maximum duty cycle clamp
should be calculated using the equation below with a
first pass guess for SS_MAXDC.
Note: Since maximum operational duty cycle occurs at
minimum system input voltage (UVLO), the voltage at the
SD_VSEC pin = 1.32V.
Max Duty Cycle Clamp (OUT pin)
=k0.522(SS_MAXDC(DC)/SD_VSEC) –
(tDELAYfOSC)
where,
SS_MAXDC(DC) = VREF(RB/(RT + RB)
SD_VSEC = 1.32V at minimum system input voltage
tDELAY = programmed delay between SOUT and OUT
k = 1.11 – 5.5e–7(fOSC)
(3)Themaximumdutycycleclampcalculatedin(2)should
be programmed to be 10% greater than the maximum
operational duty cycle calculated in (1). Simple adjust-
ment of maximum duty cycle can be achieved by adjusting
SS_MAXDC.
Figure 8. Programming SOUT to OUT Delay: tDELAY
1952 F08
DELAY
LT1952/
LT1952-1
RDELAY
tDELAY
SOUT
OUT
Programming Maximum Duty Cycle Clamp
For forward converter applications using the simplest
topology of a single MOSFET on the primary, a maximum
switch duty cycle clamp which adapts to transformer
input voltage is necessary for reliable control of the
MOSFET. This volt-second clamp provides a safeguard for
transformerresetthatpreventstransformersaturation.The
LT1952/LT1952-1SD_VSECandSS_MAXDCpinsprovidea
capacitor-less,programmablevolt-secondclampsolution
using simple resistor ratios (Figure 9).
An increase of voltage at the SD_VSEC pin causes the
maximumdutycycleclamptodecrease.DerivingSD_VSEC
from a resistor divider connected to system input voltage
creates the volt-second clamp. The maximum duty cycle
clamp can be adjusted by programming voltage on the
Figure 9. Programming Maximum Duty Cycle Clamp
SYSTEM
INPUT VOLTAGE
ADAPTIVE
DUTY CYCLE
CLAMP INPUT
MAX DUTY CYCLE
CLAMP ADJUST INPUT
*MINIMUM ALLOWABLE RT IS 10k TO
GUARANTEE SOFT-START PULL-OFF
1952 F09
SD_VSEC
SS_MAXDC
VREF
LT1952/
LT1952-1
R1
R2
RB
RT*
相關PDF資料
PDF描述
LT1952MPGN#TRPBF SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO16
LT3412AIFE 3 A SWITCHING REGULATOR, 4 kHz SWITCHING FREQ-MAX, PDSO16
LT3412AEFE#TRPBF 3 A SWITCHING REGULATOR, 4 kHz SWITCHING FREQ-MAX, PDSO16
LT3412AEUF#TRPBF 3 A SWITCHING REGULATOR, 4 kHz SWITCHING FREQ-MAX, PQCC16
LT3412AEUF#TR 3 A SWITCHING REGULATOR, 4 kHz SWITCHING FREQ-MAX, PQCC16
相關代理商/技術參數
參數描述
LT1956 制造商:LINEAR 制造商全稱:LINEAR 功能描述:100V Synchronous Switching Regulator Controller
LT1956-5 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage, 1.5A, 500kHz Step-Down Switching Regulators
LT1956EFE 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LT1956EFE#PBF 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2
LT1956EFE#TR 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*