- 您現在的位置：買賣IC網 > PDF目錄377719 > LT1952 (Linear Technology Corporation) Single Switch Synchronous Forward Controller PDF資料下載
參數資料
| 型號： | LT1952 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Single Switch Synchronous Forward Controller |
| 中文描述： | 單開關同步前進控制器 |
| 文件頁數： | 19/24頁 |
| 文件大?。?/td> | 252K |
| 代理商： | LT1952 |
LT1952
19
1952f
APPLICATIU
0.6 = k 0.522(SS_MAXDC(DC)/SD_V
SEC
) –
(t
DELAY
f
OSC
)
For SD_V
SEC
= 1.32V, f
OSC
= 200kHz and R
DELAY
= 40k
This gives k = 1 and t
DELAY
= 40ns.
Re-arranging the above equation to solve for SS_MAXDC
= V
SS(REG)
= [0.6 + (t
DELAY
f
OSC
)(SD_V
SEC
)]/(k 0.522)
= [0.6 + (40ns 200kHz)(1.32V)]/(1 0.522)
= (0.608)(1.32)/0.522 = 1.537V
Step 3: Calculate t(V
SS(REG)
) – t(V
SS(ACTIVE)
)
Recall the time for SS_MAXDC to charge to a given voltage
V
SS
is given by,
t = R
CHARGE
C
SS
(–1) ln(1 – V
SS
/SS_MAXDC(DC))
(Figure 11 gives the model for SS_MAXDC charging)
For R
T
= 35.7k, R
B
= 100k, R
CHARGE
= 26.3k
For C
SS
= 0.1
μ
F, this gives t(V
SS(ACTIVE)
)
= t(V
SS(0.8V)
) = 2.63e
4
1e
–7
(–1) ln(1 – 0.8/1.84)
= 2.63e
–3
(–1) ln(0.565) = 1.5e
–3
s
t(V
SS(REG)
) = t(V
SS(1.537V)
) = 26.3k 0.1
μ
F –1
ln(1 – 1.66/1.84) = 2.63e
–3
(–1) ln(0.146)
= 5e
–3
s
The rise time for the converter output
= t(V
SS(REG)
) – t(V
SS(ACTIVE)
) = (5 – 1.5)e
–3
s
= 3.5e
–3
s
Example (3)
Time For Maximum Duty Cycle Clamp to
Reach Within X% of Target Value
A maximum duty cycle clamp of 72% was calculated
previously in the section ‘Programming Maximum Duty
Cycle Clamp’. The programmed value used for
SS_MAXDC(DC) was 1.84V.
The time for SS_MAXDC to charge from its minimum
value V
SS(MIN)
to within X% of SS_MAXDC(DC) is given
by,
t(SS_MAXDC charge time within X% of target)
= t[(1 – (X/100) SS_MAXDC(DC)] – t(V
SS(MIN)
)
For X = 2 and V
SS(MIN)
= 0.45V, t(0.98 1.84) –
t(0.45) = t(1.803) – t(0.45)
W
U
U
From previous calculations, t(0.45) = 7.3e – 4 s.
Using previous values for R
T
, R
B
, and C
SS
,
t(1.803) = 2.63e
–4
1e
–7
(–1) ln(1 – 1.803/1.84)
= 2.63e
–3
(–1) ln(0.02) = 1.03e
–2
s
Hence the time for SS_MAXDC to charge from its mini-
mum reset threshold of 0.45V to within 2% of its target
value is given by,
t(1.803) – t(0.45) =
1.03e
–2
– 7.3e
–4
= 9.57e
–3
Forward Converter Applications
The following section covers applications where the LT1952
is used in conjunction with other LTC parts to provide
highly efficient power converters using the single switch
forward converter topology.
95% Efficient, 5V, Synchronous Forward Converter
The circuit in Figure 14 is based on the LT1952 to provide
the simplest forward power converter circuit — using only
one primary MOSFET. The SOUT pin of the LT1952 pro-
vides a synchronous control signal for the LTC1698 lo-
cated on the secondary. The LTC1698 drives secondary
side synchronous rectifier MOSFETs to achieve high effi-
ciency. The LTC1698 also serves as an error amplifier and
optocoupler driver.
Efficiency and transient response are shown in Figures 12
and 13. Peak efficiencies of 95% and ultra-fast transient
response are superior to presently available power mod-
ules. Integrated soft-start, over-current detection and
short circuit hiccup mode provide low stress, reliable
protection. In addition, the circuit in Figure 14 is an all-
ceramic capacitor solution providing low output ripple
voltage and improved reliability. The LT1952-based con-
verter can be used to replace power module converters at
a much lower cost. The LT1952 solution benefits from
thermal conduction of the system board resulting in
higher efficiencies and lower rise in component tempera-
tures. The 7mm height allows dense packaging and the
circuit can easily be adjusted to provide an output voltage
from 1.23V to 26V. Higher currents are achievable by
simple scaling of power components. The LT1952-based
solution in Figure 14 is a powerful topology for replace-
ment of a wide range of power modules.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1962-1.5 | 300mA, Low Noise, Micropower LDO Regulators(1.5V輸出,300mA, 低噪聲,微功耗,低壓差輸出穩壓器) |
| LT1962-1.8 | 300mA, Low Noise, Micropower LDO Regulators(1.8V輸出,300mA, 低噪聲,微功耗,低壓差輸出穩壓器) |
| LT1962-2.5 | 300mA, Low Noise, Micropower LDO Regulators(2.5V輸出,300mA, 低噪聲,微功耗,低壓差輸出穩壓器) |
| LT1962-3 | 300mA, Low Noise, Micropower LDO Regulators(3V輸出,300mA, 低噪聲,微功耗,低壓差輸出穩壓器) |
| LT1962-3.3 | 300mA, Low Noise, Micropower LDO Regulators(3.3V輸出,300mA, 低噪聲,微功耗,低壓差輸出穩壓器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1952-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Single Switch Synchronous Forward Controller |
| LT1952EGN | 制造商:Linear Technology 功能描述:Current Mode PWM Controller 16-Pin SSOP N |
| LT1952EGN#PBF | 功能描述:IC REG CTRLR ISO PWM CM 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LT1952EGN#TR | 制造商:Linear Technology 功能描述:Current Mode PWM Controller 16-Pin SSOP N T/R |
| LT1952EGN#TRPBF | 功能描述:IC REG CTRLR ISO PWM CM 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。