- 您現在的位置：買賣IC網 > PDF目錄377718 > LT1920CN8 (LINEAR TECHNOLOGY CORP) Precision Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | LT1920CN8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Precision Instrumentation Amplifier |
| 中文描述： | INSTRUMENTATION AMPLIFIER, 185 uV OFFSET-MAX, 1 MHz BAND WIDTH, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-8 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 329K |
| 代理商： | LT1920CN8 |
9
LT1920
Input and Output Offset Voltage
The offset voltage of the LT1920 has two components: the
output offset and the input offset. The total offset voltage
referred to the input (RTI) is found by dividing the output
offset by the programmed gain (G) and adding it to the
input offset. At high gains the input offset voltage domi-
nates, whereas at low gains the output offset voltage
dominates. The total offset voltage is:
Total input offset voltage (RTI)
= input offset + (output offset/G)
Total output offset voltage (RTO)
= (input offset G) + output offset
Reference Terminal
The reference terminal is one end of one of the four 10k
resistors around the difference amplifier. The output volt-
age of the LT1920 (Pin 6) is referenced to the voltage on
the reference terminal (Pin 5). Resistance in series with
the REF pin must be minimized for best common mode
rejection. For example, a 2
resistance from the REF pin
to ground will not only increase the gain error by 0.02%
but will lower the CMRR to 80dB.
Single Supply Operation
For single supply operation, the REF pin can be at the same
potential as the negative supply (Pin 4) provided the
output of the instrumentation amplifier remains inside the
specified operating range and that one of the inputs is at
least 2.5V above ground. The barometer application on the
front page of this data sheet is an example that satisfies
these conditions. The resistance R
SET
from the bridge
transducer to ground sets the operating current for the
bridge and also has the effect of raising the input common
mode voltage. The output of the LT1920 is always inside
the specified range since the barometric pressure rarely
goes low enough to cause the output to rail (30.00 inches
of Hg corresponds to 3.000V). For applications that re-
quire the output to swing at or below the REF potential, the
voltage on the REF pin can be level shifted. An op amp is
used to buffer the voltage on the REF pin since a parasitic
series resistance will degrade the CMRR. The application
in the back of this data sheet, Four Digit Pressure Sensor,
is an example.
THEORY OF OPERATIOU
Output Offset Trimming
The LT1920 is laser trimmed for low offset voltage so that
no external offset trimming is required for most applica-
tions. In the event that the offset needs to be adjusted, the
circuit in Figure 2 is an example of an optional offset adjust
circuit. The op amp buffer provides a low impedance to the
REF pin where resistance must be kept to minimum for
best CMRR and lowest gain error.
Input Bias Current Return Path
The low input bias current of the LT1920 (2nA) and the
high input impedance (200G
) allow the use of high
impedance sources without introducing additional offset
voltage errors, even when the full common mode range is
required. However, a path must be provided for the input
bias currents of both inputs when a purely differential
signal is being amplified. Without this path the inputs will
float to either rail and exceed the input common mode
range of the LT1920, resulting in a saturated input stage.
Figure 3 shows three examples of an input bias current
path. The first example is of a purely differential signal
source with a 10k
input current path to ground. Since the
impedance of the signal source is low, only one resistor is
impedance signal sources as shown in the second
example. Balancing the input impedance improves both
common mode rejection and DC offset. The need for input
resistors is eliminated if a center tap is present as shown
in the third example.
–
+
2
1
–IN
OUTPUT
+IN
8
3
10k
100
100
–10mV
1920 F02
V
–
V
+
10mV
5
2
3
1
6
1/2
LT1112
±
10mV
ADJUSTMENT RANGE
R
G
–
+
LT1920
REF
Figure 2. Optional Trimming of Output Offset Voltage
相關PDF資料 |
PDF描述 |
|---|---|
| LT1920C | Precision Instrumentation Amplifier |
| LT1920I | Precision Instrumentation Amplifier |
| LT1920 | Low Power, Precision Instrumentation Amplifier(低功耗,精密儀用放大器) |
| LT1930ES5 | 1A, 1.2MHz/2.2MHz, Step-Up DC/DC Converters |
| LT1930 | Constant-Current/ Constant-Voltage 1.4MHz Step-Up DC/DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1920CN8#PBF | 功能描述:IC PREC INSTRUMENTATION AMP 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:350 V/µs 增益帶寬積:180MHz -3db帶寬:320MHz 電流 - 輸入偏壓:12.5µA 電壓 - 輸入偏移:800µV 電流 - 電源:15mA 電流 - 輸出 / 通道:85mA 電壓 - 電源，單路/雙路(±):2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
| LT1920CS8 | 功能描述:IC PREC INSTRUMNTATION AMP 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:350 V/µs 增益帶寬積:180MHz -3db帶寬:320MHz 電流 - 輸入偏壓:12.5µA 電壓 - 輸入偏移:800µV 電流 - 電源:15mA 電流 - 輸出 / 通道:85mA 電壓 - 電源，單路/雙路(±):2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
| LT1920CS8#PBF | 功能描述:IC PREC INSTRUMNTATION AMP 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:350 V/µs 增益帶寬積:180MHz -3db帶寬:320MHz 電流 - 輸入偏壓:12.5µA 電壓 - 輸入偏移:800µV 電流 - 電源:15mA 電流 - 輸出 / 通道:85mA 電壓 - 電源，單路/雙路(±):2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
| LT1920CS8#PBF | 制造商:Linear Technology 功能描述:Instrumentation Amplifier IC |
| LT1920CS8#TR | 功能描述:IC AMP INSTRUMENT PREC LP 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
發布緊急采購，3分鐘左右您將得到回復。