- 您現在的位置：買賣IC網 > PDF目錄369847 > LT1813HVIS8 Voltage-Feedback Operational Amplifier PDF資料下載
參數資料
| 型號： | LT1813HVIS8 |
| 元件分類： | 運算放大器 |
| 英文描述： | Voltage-Feedback Operational Amplifier |
| 中文描述： | 電壓反饋運算放大器 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 246K |
| 代理商： | LT1813HVIS8 |
LT1813
APPLICATIO
S I
N
FOR
ATIO
U
Layout and Passive Components
The LT1813 amplifier is more tolerant of less than ideal
layouts than other high speed amplifiers. For maximum
performance (for example, fast settling) use a ground
plane, short lead lengths and RF-quality bypass capacitors
(0.01
μ
F to 0.1
μ
F). For high drive current applications, use
low ESR bypass capacitors (1
μ
F to 10
μ
F tantalum).
The parallel combination of the feedback resistor and gain
setting resistor on the inverting input combine with the
input capacitance to form a pole that can cause peaking or
oscillations. If feedback resistors greater than 2k are used,
a parallel capacitor of value
C
F
> R
G
C
IN
/R
F
should be used to cancel the input pole and optimize
dynamic performance. For applications where the DC
noise gain is 1 and a large feedback resistor is used, C
F
should be greater than or equal to C
IN
. An example would
be an I-to-V converter.
W
U
Input Considerations
Each of the LT1813 amplifier inputs is the base of an NPN
and PNP transistor whose base currents are of opposite
polarity and provide first-order bias current cancellation.
Because of variation in the matching of NPN and PNP beta,
the polarity of the input current can be positive or negative.
The offset current does not depend on beta matching and
is well controlled. The use of balanced source resistance
at each input is recommended for applications where DC
accuracy must be maximized. The inputs can withstand
differential input voltages of up to 3V without damage and
need no clamping or source resistance for protection.
Differential inputs generate the large supply currents (up
to 40mA) required for high slew rates. Typically, power
dissipation does not significantly increase in normal,
closed-loop operation because of the low duty cycle of the
transient inputs.
The device should not be used as a comparator
because
with sustained differential inputs, excessive power dissi-
pation may result.
Capacitive Loading
The LT1813 is stable with a 1000pF capacitive load which
is outstanding for a 100MHz amplifier. This is accom-
plished by sensing the load induced output pole and
adding compensation at the amplifier gain node. As the
capacitive load increases, both the bandwidth and phase
margin decrease so there will be peaking in the frequency
domain and in the transient response. Coaxial cable can be
driven directly, but for best pulse fidelity, a resistor of
value equal to the characteristic impedance of the cable
(i.e., 75
) should be placed in series with the output. The
other end of the cable should be terminated with the same
value resistor to ground.
Slew Rate
The slew rate is proportional to the differential input
voltage. Highest slew rates are therefore seen in the
lowest gain configurations. For example, a 5V output step
in a gain of 10 has a 0.5V input step, whereas in unity gain
there is a 5V input step. The LT1813 is tested for slew rate
in a gain of –1. Lower slew rates occur in higher gain
configurations.
Power Dissipation
The LT1813 combines high speed and large output drive
in a small package. It is possible to exceed the maximum
junction temperature under certain conditions. Maximum
junction temperature (T
J
) is calculated from the ambient
temperature (T
A
) and power dissipation (P
D
) as follows:
LT1813CS8: T
J
= T
A
+ (P
D
150
°
C/W)
Power dissipation is composed of two parts. The first is
due to the quiescent supply current and the second is
due to on-chip dissipation caused by the load current.
The worst-case load induced power occurs when the
output voltage is at 1/2 of either supply voltage (or the
maximum swing if less than 1/2 supply voltage). For each
amplifier:
P
DMAX
= (V
+
– V
–
)(I
SMAX
) + (V
+
/2)
2
/R
L
or
P
DMAX
= (V
+
– V
–
)(I
SMAX
) + (V
+
– V
OMAX
)(V
OMAX
/R
L
)
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| LT1812CS5 | Voltage-Feedback Operational Amplifier |
| LT1812CS6 | Operational Amplifier |
| LT1812IS5 | Voltage-Feedback Operational Amplifier |
| LT1812IS6 | Operational Amplifier |
| LT1813HVCS8 | OP-AMP|DUAL|BIPOLAR|TSSOP|8PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1813HVIS8#PBF | 功能描述:IC OPAMP LOWPWR HISPD DUAL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT1813HVIS8#TR | 功能描述:IC OPAMP DUAL 3MA LP HS HV 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT1813HVIS8#TRPBF | 功能描述:IC OPAMP LOWPWR HISPD DUAL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| LT1813IDD | 功能描述:IC OP AMP DUAL LOW PWR HS 8-DFN RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| LT1813IDD#PBF | 功能描述:IC OP AMP DUAL LOW PWR HS 8-DFN RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。