- 您現在的位置：買賣IC網 > PDF目錄10682 > LT1712IGN (Linear Technology)IC COMP R-R I/O DUAL LP 16SSOP PDF資料下載
參數資料
| 型號： | LT1712IGN |
| 廠商： | Linear Technology |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COMP R-R I/O DUAL LP 16SSOP |
| 標準包裝： | 100 |
| 系列： | UltraFast™ |
| 類型： | 帶鎖銷 |
| 元件數： | 2 |
| 輸出類型： | CMOS，補充型，滿擺幅，TTL |
| 電壓 - 電源，單路/雙路(±)： | 2.4 V ~ 12 V，±2.4 V ~ 6 V |
| 電壓 - 輸入偏移（最小值）： | 5mV @ 5V |
| 電流 - 輸入偏壓（最小值）： | 5µA @ 5V |
| 電流 - 輸出（標準）： | 20mA |
| 電流 - 靜態（最大值）： | 22mA |
| CMRR, PSRR（標準）： | 75dB CMRR，85dB PSRR |
| 傳輸延遲（最大）： | 6ns |
| 磁滯： | 100mV |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 安裝類型： | 表面貼裝 |
| 包裝： | 管件 |
7
LT1711/LT1712
UU
U
PI FU CTIO S
LT1712
– IN A (Pin 1): Inverting Input of A Channel Comparator.
+ IN A (Pin 2): Noninverting Input of A Channel
Comparator.
V – (Pins 3, 6): Negative Supply Voltage, Usually – 5V. Pins
3 and 6 should be connected together externally.
V + (Pins 4, 5): Positive Supply Voltage, Usually 5V. Pins
4 and 5 should be connected together externally.
+ IN B (Pin 7): Noninverting Input of B Channel
Comparator.
– IN B (Pin 8): Inverting Input of B Channel Comparator.
LATCH ENABLE B (Pin 9): Latch Enable Input of B Channel
Comparator. With a logic high, the B output is latched.
GND (Pin 10): Ground Supply Voltage of B Channel
Comparator, Usually 0V.
Q B (Pin 11): Noninverting Output of B Channel
Comparator.
Q B (Pin 12): Inverting Output of B Channel
Comparator.
Q A (Pin 13): Inverting Output of A Channel
Comparator.
Q A (Pin 14): Noninverting Output of A Channel
Comparator.
GND (Pin 15): Ground Supply Voltage of A Channel
Comparator, Usually 0V
LATCH ENABLE A (Pin 16): Latch Enable Input of A
Channel Comparator. With a logic high, the A output is
latched.
APPLICATIO S I FOR ATIO
WU
UU
Common Mode Considerations
The LT1711/LT1712 are specified for a common mode
range of – 5.1V to 5.1V on a
±5V supply, or a common
mode range of – 0.1V to 5.1V on a single 5V supply. A more
general consideration is that the common mode range is
from 100mV below the negative supply to 100mV above
the positive supply, independent of the actual supply
voltage. The criteria for common mode limit is that the
output still responds correctly to a small differential input
signal.
When either input signal falls outside the common mode
limit, the internal PN diode formed with the substrate can
turn on resulting in significant current flow through the
die. Schottky clamp diodes between the inputs and the
supply rails speed up recovery from excessive overdrive
conditions by preventing these substrate diodes from
turning on.
Input Bias Current
Input bias current is measured with the outputs held at
2.5V with a 5V supply voltage. As with any rail-to-rail
differential input stage, the LT1711/LT1712 bias current
flows into or out of the device depending upon the com-
mon mode level. The input circuit consists of an NPN pair
and a PNP pair. For inputs near the negative rail, the NPN
pair is inactive, and the input bias current flows out of the
device; for inputs near the positive rail, the PNP pair is
inactive, and these currents flow into the device. For inputs
far enough away from the supply rails, the input bias
current will be some combination of the NPN and PNP bias
currents. As the differential input voltage increases, the
input current of each pair will increase for one of the inputs
and decrease for the other input. Large differential input
voltages result in different input currents as the input
stage enters various regions of operation. To reduce the
influence of these changing input currents on system
operation, use a low source resistance.
Latch Pin Dynamics
The internal latches of the LT1711/LT1712 comparators
retain the input data (output latched) when their respec-
tive latch pin goes high. The latch pin will float to a low
state when disconnected, but it is better to ground the
相關PDF資料 |
PDF描述 |
|---|---|
| VE-2VR-IX-B1 | CONVERTER MOD DC/DC 7.5V 75W |
| LT1116CS8 | IC COMPARATOR 12NS SINGLE 8SOIC |
| AD9609BCPZ-20 | IC ADC 10BIT 20MSPS LP 32LFCSP |
| CMP401GSZ-REEL | IC COMPARATOR LV 23NS 16SOIC |
| VE-2VP-IX-B1 | CONVERTER MOD DC/DC 13.8V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1712IGN#PBF | 功能描述:IC COMP R-R I/O DUAL LP 16SSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:UltraFast™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
| LT1712IGN#TR | 功能描述:IC COMP R-R I/O DUAL LP 16SSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 比較器 系列:UltraFast™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
| LT1712IGN#TRPBF | 功能描述:IC COMP R-R I/O DUAL LP 16SSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:UltraFast™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
| LT1713 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UNDERSTANDING THE SUBJECT IS CUSTOMER SERVICE |
| LT1713CMS8 | 功能描述:IC COMP R-R I/O SINGLE LP 8MSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 比較器 系列:UltraFast™ 標準包裝:25 系列:- 類型:帶電壓基準 元件數:4 輸出類型:CMOS，開路漏極，TTL 電壓 - 電源，單路/雙路(±):2 V ~ 11 V，±1 V ~ 5.5 V 電壓 - 輸入偏移（最小值）:10mV @ 5V 電流 - 輸入偏壓（最小值）:- 電流 - 輸出（標準）:0.015mA @ 5V 電流 - 靜態（最大值）:8.5µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:12µs 磁滯:50mV 工作溫度:0°C ~ 70°C 封裝/外殼:16-DIP（0.300"，7.62mm） 安裝類型:通孔 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。