- 您現在的位置：買賣IC網 > PDF目錄385501 > LT1684 (Linear Technology Corporation) Micropower Ring Tone Generator PDF資料下載
參數資料
| 型號： | LT1684 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Micropower Ring Tone Generator |
| 中文描述： | 微鈴聲發生器 |
| 文件頁數： | 5/16頁 |
| 文件大小： | 221K |
| 代理商： | LT1684 |
5
LT1684
IN B (Pin 1):
PWM Negative Input. Input is isolated from
digital source by ~100pF series capacitor. A 10k resistor
can be connected to the IN B pin in series with the isolation
capacitor for transient protection. The PWM receiver imple-
ments a diode forward drop of input hysteresis (relative to
IN A). This hysteresis and internal signal limiting assure
common mode glitch rejection with isolation capacitor
mismatches up to 2:1. For maximum performance, how-
ever, effort should be made to match the two PWM input
isolation capacitors. Pin IN B is differentially clamped to
pin IN A through back-to-back diodes. This results in a
high impedance differential input through
±
100mV be-
yond the input thresholds. 5k internal input resistors yield
a 10k (nominal) differential overdrive impedance.
COMP1 (Pin 2):
Output Amplifier Primary Compensation.
Connect a 100pF capacitor from pin COMP1 to pin OUT.
COMP2 (Pin 3):
Output Amplifier Secondary Compensa-
tion. Connect a 20pF capacitor from pin COMP2 to pin
OUT.
LIM
–
(Pin 4):
Output Amplifier Current Sink Limit. Pin
implements I
OUT
R = V
BE
current clamp. Internal clamp
resistor has a typical value of 3.5
. For maximum current
drive capability (190mA typical) short pin to pin V
–
.
Reduction of current sink capability is achieved by placing
additional resistance from pin LIM
–
to pin V
–
. (i.e. An
external 3.5
resistance from pin LIM
–
to pin V
–
will
reduce the current sinking capability of the output ampli-
fier by approximately 50%.)
V
–
(Pin 5):
Local Negative Supply. Typically connected to
the source of the active tracking supply P-channel MOSFET.
V
–
rail voltage is GATE
–
self-bias voltage less the MOSFET
V
GS
. Typical P-channel MOSFET characteristics provide
AT
REF
– V
–
≈
10V.
GATE
–
(Pin 6):
Negative Power Supply FET Gate Drive. Pin
sources current from pull-down resistor to bias gate of
active tracking supply P-channel MOSFET. Self-biases to
a typical value of –14V, referenced to pin AT
REF
. Pull-down
resistor value is determined such that current sourced
from the GATE
–
pin remains greater than 50
μ
A at mini-
mum output signal voltage and less than 10mA at maxi-
mum output signal voltage.
AT
REF
(Pin 7):
Active Tracking Supply Reference. Typi-
cally connected to pin OUT. Pin bias current is the differ-
ence between the magnitudes of GATE
+
pin bias and
GATE
–
pin bias (I
ATREF
=
I
GATE
+
–
I
GATE
–
).
OUT (Pin 8):
Ring Tone Output Pin. Output of active filter
amplifier/buffer. Used as reference voltage for internal
functions of IC. Usually shorted to pin AT
REF
to generate
reference for active tracking supply circuitry. Connect a 1A
(1N4001-type) diode between V
+
and OUT and a
1A Schottky diode from V
–
to OUT for line transient
protection.
LIM
+
(Pin 9):
Output Amplifier Current Source Limit. Pin
implements I
OUT
R = V
BE
current clamp. Internal clamp
resistor has a typical value of 3.5
. For maximum current
drive capability (190mA typical) short pin LIM
+
to pin
OUT. Reduction of current source capability is achieved by
placing additional resistance from pin LIM
+
to pin OUT.
(i.e. An external 3.5
resistance from pin LIM
+
to pin OUT
will reduce the current sourcing capability of the output
amplifier by approximately 50%.)
V
+
(Pin 10):
Local Positive Supply. Typically connected to
the source of the active tracking supply N-channel MOSFET.
This condition should be made using a ferrite bead.
Operating V
+
rail voltage is GATE
+
self-bias voltage less
the MOSFET V
GS
. Typical N-channel MOSFET characteris-
tics provide V
+
– AT
REF
≈
10V.
GATE
+
(Pin 11):
Positive Power Supply FET Gate Drive.
Pin sinks current from pull-up resistor to bias gate of
active tracking supply N-channel MOSFET. Self-biases to
a typical value of 14V, referenced to pin AT
REF
. Pull-up
resistor value is determined such that sink current into
GATE
+
pin remains greater than 50
μ
A at maximum output
signal voltage and less than 10mA at minimum output
signal voltage.
AMPIN (Pin 12)
: Output Amplifier Input. Connected to
external filter components through series protection re-
sistor (usually 5k). Thevenin DC resistance of external
filter and protection components should be 10k for opti-
mum amplifier offset performance. See Applications In-
formation section.
PIU
相關PDF資料 |
PDF描述 |
|---|---|
| LT1684CN | Micropower Ring Tone Generator |
| LT1684CS | Micropower Ring Tone Generator |
| LT1684IN | Micropower Ring Tone Generator |
| LT1684IS | Micropower Ring Tone Generator |
| LT1715 | 4ns, 150MHz Dual Comparator with Independent Input/Output Supplies |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1684CN | 功能描述:IC RING TONE GENERATOR 14-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| LT1684CN#PBF | 功能描述:IC RING TONE GENERATOR 14-DIP RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| LT1684CS | 功能描述:IC RING TONE GENERATOR 14-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| LT1684CS#PBF | 功能描述:IC RING TONE GENERATOR 14-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| LT1684CS#TR | 功能描述:IC GENERATOR RING TONE 14SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
發布緊急采購，3分鐘左右您將得到回復。