- 您現在的位置：買賣IC網 > PDF目錄377708 > LT1579CGN-3.3 (LINEAR TECHNOLOGY CORP) 300mA Dual Input Smart Battery Backup Regulator PDF資料下載
參數資料
| 型號： | LT1579CGN-3.3 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 300mA Dual Input Smart Battery Backup Regulator |
| 中文描述： | 3.3 V FIXED POSITIVE LDO REGULATOR, 0.75 V DROPOUT, PDSO16 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP-16 |
| 文件頁數： | 14/20頁 |
| 文件大?。?/td> | 352K |
| 代理商： | LT1579CGN-3.3 |
14
LT1579
if V
IN2
>V
IN1
, so typically only 3
μ
A. The primary input will
automatically go into standby mode as the primary input
drops below the output voltage. The primary input can also
be forced into standby mode by asserting the SS pin. In
either case, the current drawn from the primary input is
reduced to a maximum of 7
μ
A.
Shutdown
The LT1579 has a low power shutdown state where all
functions of the device are shut off. The device is put into
shutdown mode when the shutdown pin is pulled below
0.7V. The quiescent current in shutdown has three com-
ponents: 2
μ
A drawn from the primary, 2
μ
A drawn from the
secondary and 3
μ
A which is drawn from the higher of the
two inputs.
Protecting Batteries Using Secondary Select (SS)
Some batteries, such as lithium-ion cells, are sensitive to
deep discharge conditions. Discharging these batteries
below a certain threshold severely shortens battery life. To
prevent deep discharge of the primary cells, the LT1579
secondary select (SS) pin can be used to switch power
draw from the primary input to the secondary. When this
pin is pulled low, current out of the primary is reduced to
2
μ
A. A low-battery detector with the trip point set at the
critical discharge point can signal the low battery condi-
tion and force the switchover to the secondary as shown
in Figure 2. The second low-battery comparator can be
used to set a latch to shutdown the LT1579 (see the Typical
Applications).
APPLICATIO
S I
FOR
ATIO
U
W
U
U
Low-Battery Comparators
There are two independent low-battery comparators in the
LT1579. This allows for individual monitoring of each
input. The inverting inputs of both comparators are con-
nected to an internal 1.5V reference. The low-battery
comparator trip point is set by an external resistor divider
as shown in Figure 3. The current in R1 at the trip point is
1.5V/R1. The current in R2 is equal to the current in R1.
The low-battery comparator input bias current, 2nA flow-
ing out of the pin, is negligible and may be ignored. The
value of R1 should be less than 1.5M in order to minimize
errors in the trip point. The value of R2 for a given trip point
is calculated using the formulas in Figure 3.
The low-battery comparators have a small amount of
hysteresis built-in. The amount of hysteresis is dependent
upon the output sink current (I
SINK
) when the comparator
is tripped low. At no load, comparator hysteresis is zero,
increasing to a maximum of 18mV for sink currents above
20
μ
A. See the curve of Low-Battery Comparator Hyster-
esis in the Typical Performance Characteristics. If larger
amounts of hysteresis are desired, R3 and D1 can be
added. D1 can be any small diode, typically a 1N4148.
Calculating V
LBO
can be done using a load line on the curve
of Logic Flag Output Voltage vs Sink Current in the Typical
Performance Characteristics.
Figure 2. Connecting SS to Low-Battery Detector
Output to Prevent Damage to Batteries
LBO
SS
GND
V
CC
R
P
1579 F02
–
+
R2
R1
1.5V
R4
D1
R3
V
TRIP
V
OUT
LBI
LBO
I
SINK
LTC1579 F02
R2 = (V
TRIP
– 1.5V)
R1
1.5V
(
)
HYSTERESIS = V
HYST
1 +
FOR I
SINK
≥
20
μ
A, V
HYST
= 18mV,
FOR I
< 20
μ
A, SEE THE TYPICAL
PERFORMANCE CHARACTERISTICS
R2
R1
)
R3 = (1.5V + V
HYST
– 0.6V – V
LBO
)(R2)
V
HYST(ADDED)
FOR ADDED HYSTERESIS
Figure 3. Low-Battery Comparator Operation
相關PDF資料 |
PDF描述 |
|---|---|
| LT1579CGN-5 | 300mA Dual Input Smart Battery Backup Regulator |
| LT1579 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LT1580C | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LT1580-2.5 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LT1580CR-2.5 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1579CGN-5 | 功能描述:IC LDO REG SMART DUAL 5V 16SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| LT1579CGN-5#PBF | 功能描述:IC LDO REG SMART DUAL 5V 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| LT1579CGN-5#TR | 功能描述:IC REG LDO SMART DUAL 5V 16SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LT1579CGN-5#TRPBF | 功能描述:IC LDO REG SMART DUAL 5V 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| LT1579CS | 功能描述:IC LDO REG SMART DUAL ADJ 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。