- 您現在的位置：買賣IC網 > PDF目錄377707 > LT1568 (Linear Technology Corporation) Very Low Noise, High Frequency Active RC, Filter Building Block PDF資料下載
參數資料
| 型號： | LT1568 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Very Low Noise, High Frequency Active RC, Filter Building Block |
| 中文描述： | 極低噪聲，高頻有源RC，濾波器積木 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 271K |
| 代理商： | LT1568 |
LT1568
8
1568f
PIU
V
+
(Pins 1, 16):
The V
+
positive supply voltage pins should
be tied together and bypassed with a 0.1
μ
F capacitor to an
adequate analog ground plane using the shortest possible
wiring.
INVA, INVB (Pins 2, 15):
Inverting Input. Each of the INV
pins is an inverting input of an op amp. Note that the INV
pins are high impedance, and are susceptible to coupling
of unintended signals. External parasitic capacitance on
the INV nodes will also affect the frequency response of
the filter sections. For these reasons, printed circuit con-
nections to the INV pins must be kept as short as possible.
SA, SB (Pins 3, 14):
Summing Pins. These pins are a
summing junction for input signals. Stray capacitance on
the SA or SB pins may cause “small” frequency errors of
the frequency response near the cutoff frequency (or
center frequency). The three external resistors for each
section should be located as close as possible to the SA or
SB pin to minimize stray capacitance (one picofarad of
stray capacitance may add up to 0.1% frequency error).
OUTA, OUTB (Pins 4, 13):
Lowpass Output. These pins
are the rail-to-rail outputs of op amps. Each output is
designed to drive a nominal net load of 400
and 30pF.
OUTA, OUTB (Pins 5, 12):
These pins are the inverted
versions of the OUTA and OUTB outputs respectively. Each
output is designed to drive a nominal load of 400
and
30pF.
GNDA (Pin 6):
GNDA serves as the common mode refer-
ence voltage for section A. It should be tied to the analog
ground plane in a dual supply system. In a single-supply
system, an internal resistor divider can be used to estab-
lish a half-supply reference point. In that case, GNDA must
be bypassed to V
–
(Pins 8, 9) by a 0.1
μ
F capacitor.
NC (Pin 7):
This pin is not connected internally and can be
connected to ground.
V
–
(Pins 8, 9):
The V
–
negative supply voltage pins should
be tied together and bypassed to GND by a 0.1
μ
F capacitor
in a dual-supply system. In a single-supply system, tie
these pins to the ground plane.
EN (Pin 10):
ENABLE. When the EN input goes high or is
open circuited, the LT1568 enters a shutdown state which
reduces the supply current to approximately 0.5mA
(V
S
= 5V). The OUTA, OUTB, OUTA and OUTB pins
assume high impedance states. GNDA will continue to be
biased at half-supply. If an input signal is applied to a
complete filter circuit while the LT1568 is in shutdown,
some signal will normally flow to the output through
passive components around the inactive IC.
EN is connected to V
+
through an internal pull-up resistor
of approximately 40k. This defaults the LT1568 to the
shutdown state if the EN pin is left floating. Therefore, the
user must connect the EN pin to a voltage equal to or less
than (V
+
– 2.1)V to enable the part for normal operation.
(For example, if V
+
is 5V, then to enable the part the EN pin
voltage should be 2.9V or less.)
GNDB (Pin 11):
GNDB serves as the common mode
reference voltage for section B. It should be tied to the
analog ground plane in a dual supply system. In a single-
supply system, GNDB can be tied to GNDA to set the
common mode voltage at half-supply. If it is tied to
another reference voltage, GNDB should be bypassed to
V
–
(Pins 8, 9) by a 0.1
μ
F capacitor.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1568IGN | D52 - STRAIN RELIEF OPEN STRT MIL |
| LT1568CGN | Very Low Noise, High Frequency Active RC, Filter Building Block |
| LT1571-5 | Constant-Current/ Constant-Voltage Battery Charger with Preset Voltage and Termination Flag |
| LT1571EGN-1 | Constant-Current/ Constant-Voltage Battery Charger with Preset Voltage and Termination Flag |
| LT1571EGN-2 | Constant-Current/ Constant-Voltage Battery Charger with Preset Voltage and Termination Flag |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1568CGN | 功能描述:IC FILTER BUILDING BLOCK 16SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LT1568CGN#PBF | 功能描述:IC FILTER BUILDING BLOCK 16SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LT1568CGN#TR | 功能描述:IC BLOCK BUILD FLTR LONOS 16SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LT1568CGN#TRPBF | 功能描述:IC BLOCK BUILD FLTR LONOS 16SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LT1568CGNPBF | 制造商:LINEAR_DIMENSIONS 制造商全稱:LINEAR_DIMENSIONS 功能描述:Very Low Noise, High Frequency Active RC, Filter Building Block |
發布緊急采購，3分鐘左右您將得到回復。