- 您現在的位置：買賣IC網 > PDF目錄377706 > LT1513IR (LINEAR TECHNOLOGY CORP) SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger PDF資料下載
參數資料
| 型號： | LT1513IR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| 中文描述： | 5.4 A BATTERY CHARGE CONTROLLER, 580 kHz SWITCHING FREQ-MAX, PSSO7 |
| 封裝： | PLASTIC, D2PAK-7 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 299K |
| 代理商： | LT1513IR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
8
LT1513/LT1513-2
APPLICATIO
S I
FOR
ATIO
U
shown in the maximum charging current graph. Higher
inductance values give slightly higher maximum charging
current, but are larger and more expensive. A low loss toroid
core such as Kool M
μ
, Molypermalloy or Metglas
is
recommended. Series resistance should be less than 0.04
for each winding. “Open core” inductors, such as rods or
barrels are not recommended because they generate large
magnetic fields which may interfere with other electronics
close to the charger.
W
U
U
Input Capacitor
The SEPIC topology has relatively low input ripple current
compared to other topologies and higher harmonics are
especially low. RMS ripple current in the input capacitor is
less than 0.25A with L = 10
μ
H and less than 0.5A with
L = 5
μ
H. A low ESR 22
μ
F, 25V solid tantalum capacitor (AVX
type TPS or Sprague type 593D) is adequate for most
applications with the following caveat. Solid tantalum
capacitors can be destroyed with a very high turn-on surge
current such as would be generated if a low impedance input
source were “hot switched” to the charger input. If this
condition can occur, the input capacitor should have the
highest possible voltage rating, at least twice the surge input
voltage if possible. Consult with the capacitor manufacturer
before a final choice is made. A 4.7
μ
F ceramic capacitor such
as the one used for the coupling capacitor can also be used.
These capacitors do not have a turn-on surge limitation. The
input capacitor must be connected directly to the V
IN
pin and
the ground plane close to the LT1513.
Output Capacitor
It is assumed as a worst case that all the switching output
ripple current from the battery charger could flow in the
output capacitor. This is a desirable situation if it is neces-
sary to have very low switching ripple current in the battery
itself. Ferrite beads or line chokes are often inserted in series
with the battery leads to eliminate high frequency currents
that could create EMI problems. This forces all the ripple
current into the output capacitor. Total RMS current into the
capacitor has a maximum value of about 1A, and this is
handled with the two paralleled 22
μ
F, 25V capacitors shown
in Figure 1. These are AVX type TPS or Sprague type 593D
surface mount solid tantalum units intended for switching
applications. Do not substitute other types without ensuring
that they have adequate ripple current ratings. See Input
Capacitor section for details of surge limitation on solid
tantalum capacitors if the battery may be “hot switched” to
the output of the charger.
Coupling Capacitor
C2 in Figure 1 is the coupling capacitor that allows a SEPIC
converter topology to work with input voltages either higher
or lower than the battery voltage. DC bias on the capacitor is
equal to input voltage. RMS ripple current in the coupling
capacitor has a maximum value of about 1A at full charging
current. A conservative formula to calculate this is:
I
I
V
(
V
V
(
COUP RMS
CHRG
IN
2
BAT
)
IN
(
)
)( . )
1 1
=
+
(1.1 is a fudge factor to account for inductor ripple current
and other losses)
With I
CHRG
= 1.2A, V
IN
= 15V and V
BAT
= 8.2V, I
COUP
= 1.02A.
The recommended capacitor is a 4.7
μ
F ceramic type from
Marcon or Tokin. These capacitors have extremely low ESR
and high ripple current ratings in a small package. Solid
tantalum units can be substituted if their ripple current rating
is adequate, but typical values will increase to 22
μ
F or more
to meet the ripple current requirements.
Diode Selection
The switching diode should be a Schottky type to minimize
both forward and reverse recovery losses. Average diode
current is the same as output charging current, so this will be
under 2A. A 3A diode is recommended for most applications,
although smaller devices could be used at reduced charging
current. Maximum diode reverse voltage will be equal to
input voltage plus battery voltage.
Diode reverse leakage current will be of some concern
during charger shutdown. This leakage current is a direct
drain on the battery when the charger is not powered. High
Kool M
μ
is a registered trademark of Magnetics, Inc.
Metglas is a registered trademark of AlliedSignal Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1513IT7-2 | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513CT7-2 | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513 | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger(初級線圈感應轉換，恒定電流或可編程電流/恒定電壓電池充電器) |
| LT1521-3 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LT1521-3.3 | Paired Cable; Jacket Material:Polyvinylchloride (PVC); Leaded Process Compatible:Yes RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1513IR#PBF | 功能描述:IC BATT CHRGR CONST/PROG I/V 7DD RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LT1513IR#TR | 功能描述:IC CHARGER BATTERY CONST V/I 7DD RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LT1513IR#TRPBF | 功能描述:IC BATT CHRGR CONST/PROG I/V 7DD RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LT1513IR-2 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513IRPBF | 制造商:Linear Technology 功能描述:Battery Charger SEPIC Con/Progr. D2PAK-8 |
發布緊急采購，3分鐘左右您將得到回復。