- 您現在的位置：買賣IC網 > PDF目錄377705 > LT1513CR-2 (LINEAR TECHNOLOGY CORP) SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger PDF資料下載
參數資料
| 型號： | LT1513CR-2 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| 中文描述： | 5.4 A BATTERY CHARGE CONTROLLER, 580 kHz SWITCHING FREQ-MAX, PSSO7 |
| 封裝： | PLASTIC, D2PAK-7 |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 299K |
| 代理商： | LT1513CR-2 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
5
LT1513/LT1513-2
PI
FU
CTIO
N
S
U
U
V
C
(Pin 1):
The compensation pin is primarily used for
frequency compensation, but it can also be used for soft
starting and current limiting. It is the output of the error
amplifier and the input of the current comparator. Peak
switch current increases from 0A to 3.6A as the V
C
voltage
varies from 1V to 1.9V. Current out of the V
C
pin is about
200
μ
A when the pin is externally clamped below the
internal 1.9V clamp level. Loop frequency compensation
is performed with a capacitor or series RC network from
the V
C
pin directly to the ground pin avoid ground loops).
FB (Pin 2):
The feedback pin is used for positive output
voltage sensing. The R1/R2 voltage divider connected to
FB defines Li-Ion float voltage at full charge, or acts as a
voltage limiter for NiCd or NiMH applications. FB is the
inverting input to the voltage error amplifier. Input bias
current is typically 300nA, so divider current is normally
set to 100
μ
A to swamp out any output voltage errors due
to bias current. The noninverting input of this amplifier is
tied internally to a 1.245V reference. The grounded end of
the output voltage divider should be connected directly to
the LT1513 ground pin (avoid ground loops).
I
FB
(Pin 3):
The current feedback pin is used to sense
charging current. It is the input to a current sense amplifier
that controls charging current when the battery voltage is
below a programmed limit. During constant-current
operation, the LT1513 I
FB
pin regulates at –100mV. Input
resistance of this pin is 5k
, so filter resistance (R4,
Figure 1) should be less than 50
. The 39
, 0.22
μ
F filter
shown in Figure 1 is used to convert the pulsating current
in the sense resistor to a smooth DC current feedback
signal. The LT1513-2 I
FB
pin regulates at 0mV to provide
programmable current limit. The current through R5,
Figure 5, is balanced by the current through R4, program-
ming the maximum voltage across R3.
GND (Pin 4):
The ground pin is common to both control
circuitry and switch current. V
C
, FB and S/S signals must
be Kelvin and connected as close as possible to this pin.
The TAB of the R package should also be connected to the
power ground.
V
SW
(Pin 5):
The switch pin is the collector of the power
switch, carrying up to 3A of current with fast rise and fall
times. Keep the traces on this pin as short as possible to
minimize radiation and voltage spikes. In particular, the
path in Figure 1 which includes SW to C2, D1, C1 and
around to the LT1513 ground pin should be as short as
possible to minimize voltage spikes at switch turn-off.
S/S (Pin 6):
This pin can be used for shutdown and/or
synchronization. It is logic level compatible, but can be
tied to V
IN
if desired. It defaults to a high ON state when
floated. A logic low state will shut down the charger to a
micropower state. Driving the S/S pin with a continuous
logic signal of 600kHz to 800kHz will synchronize switch-
ing frequency to the external signal. Shutdown is avoided
in this mode with an internal timer.
V
IN
(Pin 7):
The input supply pin should be bypassed with
a low ESR capacitor located right next to the IC chip. The
grounded end of the capacitor must be connected directly
to the ground plane to which the TAB is connected.
TAB:
The TAB on the surface mount R package is electri-
cally connected to the ground pin, but a low inductance
connection must be made to both the TAB and the pin for
proper circuit operation. See suggested PC layout in
Figure 4.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1513IR-2 | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513C | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513CR | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513I | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513IR | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1513CRPBF | 制造商:Linear Technology 功能描述:LT1513CRPBF |
| LT1513CT7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management |
| LT1513CT7-2 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513I | 制造商:LINER 制造商全稱:Linear Technology 功能描述:SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513IR | 功能描述:IC BATT CHRGR CONST/PROG I/V 7DD RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。