- 您現在的位置：買賣IC網 > PDF目錄377705 > LT1512IS8 (LINEAR TECHNOLOGY CORP) SEPIC Constant-Current/ Constant-Voltage Battery Charger PDF資料下載
參數資料
| 型號： | LT1512IS8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SEPIC Constant-Current/ Constant-Voltage Battery Charger |
| 中文描述： | 2.7 A BATTERY CHARGE CONTROLLER, 580 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SOP-8 |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 261K |
| 代理商： | LT1512IS8 |
4
LT1512
TYPICAL PERFOR
M
A
N
CE CHARACTERISTICS
Minimum Peak-to-Peak
Synchronization Voltage vs Temp
Feedback Input Current
vs Temperature
Negative Feedback Input Current
vs Temperature
TEMPERATURE (
°
C)
–50
0
M
P
)
0.5
1.0
1.5
2.0
0
50
100
150
1512 G04
2.5
3.0
–25
25
75
125
f
SYNC
= 700kHz
TEMPERATURE (
°
C)
–50
F
400
500
600
150
1512 G05
300
200
0
0
50
100
100
800
700
–25
25
75
125
V
FB
= V
REF
TEMPERATURE (
°
C)
–50
–50
N
μ
A
–30
0
0
50
75
1512 G06
–40
–10
–20
–25
25
100 125
150
PI
FU
CTIO
N
S
U
U
V
C
:
The compensation pin is primarily used for frequency
compensation, but it can also be used for soft starting and
current limiting. It is the output of the error amplifier and
the input of the current comparator. Peak switch current
increases from 0A to 1.8A as the V
C
voltage varies from 1V
to 1.9V. Current out of the V
C
pin is about 200
μ
A when the
pin is externally clamped below the internal 1.9V clamp
level. Loop frequency compensation is performed with a
capacitor or series RC network from the V
C
pin directly to
the ground pin (avoid ground loops).
FB:
The feedback pin is used for positive output voltage
sensing. This pin is the inverting input to the voltage error
amplifier. The R1/R2 voltage divider connected to FB
defines Li-Ion float voltage at full charge, or acts as a
voltage limiter for NiCd or NiMH applications. Input bias
current is typically 300nA, so divider current is normally
set to 100
μ
A to swamp out any output voltage errors due
to bias current. The noninverting input of this amplifier is
tied internally to a 1.245V reference. The grounded end of
the output voltage divider should be connected directly to
the LT1512 ground pin (avoid ground loops).
I
FB
:
The current feedback pin is used to sense charging
current. It is the input to a current sense amplifier that
controls charging current when the battery voltage is
below the programmed voltage. During constant-current
operation, the I
FB
pin regulates at –100mV. Input resis-
tance of this pin is 5k
, so filter resistance (R4, Figure 1)
should be less than 50
. The 24
, 0.22
μ
F filter shown in
Figure 1 is used to convert the pulsating current in the
sense resistor to a smooth DC current feedback signal.
S/S:
This pin can be used for shutdown and/or synchroni-
zation. It is logic level compatible, but can be tied to V
IN
if
desired. It defaults to a high ON state when floated. A logic
low state will shut down the charger to a micropower state.
Driving the S/S pin with a continuous logic signal of
600kHz to 800kHz will synchronize switching frequency to
the external signal. Shutdown is avoided in this mode with
an internal timer.
V
IN
:
The input supply pin should be bypassed with a low
ESR capacitor located right next to the IC chip. The
grounded end of the capacitor must be connected directly
to the ground plane to which the GND pin is connected.
GND S, GND:
The LT1512 uses separate ground pins for
switch current (GND) and the control circuitry (GND S).
This isolates the control ground from any induced voltage
created by fast switch currents. Both pins should be tied
directly to the ground plane, but the external control
circuit components such as the voltage divider, frequency
compensation network and I
FB
bypass capacitor should
相關PDF資料 |
PDF描述 |
|---|---|
| LT1512 | SEPIC (Single-Ended Primary Inductance Converter) Constant-Current/ Constant-Voltage Battery Charger(初級線圈感應轉換，恒定電流/恒定電壓電池充電器) |
| LT1513-2 | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513CR-2 | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513IR-2 | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
| LT1513C | SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1512IS8#PBF | 功能描述:IC BATT CHRGR CONST I/V 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LT1512IS8#TR | 功能描述:IC CHARGER BATT CONST V/I 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LT1512IS8#TRPBF | 功能描述:IC BATT CHRGR CONST I/V 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LT1513 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:SEPIC Constant- or Programmable-Current/ Constant-Voltage Battery Charger |
發布緊急采購，3分鐘左右您將得到回復。