- 您現在的位置：買賣IC網 > PDF目錄377751 > LT1485 (Linear Technology Corporation) Differential Bus Transceiver PDF資料下載
參數資料
| 型號： | LT1485 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Differential Bus Transceiver |
| 中文描述： | 差分總線收發器 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 257K |
| 代理商： | LT1485 |
9
LTC1485
U
S
A
O
PPLICATI
U
U
Figure 12. Termination Effects
1485 F12
DX
DRIVER
RECEIVER
RX
PROBE HERE
Rt = 120
Rt = 47
Rt = 470
R
t
AC Cable Termination
Cable termination resistors are necessary to prevent un-
wanted reflections, but they consume power. The typical
differential output voltage of the driver is 2V when the
cable is terminated with two 120
resistors, causing
33mA of DC current to flow in the cable when no data is
being sent. This DC current is about 10 times greater than
the supply current of the LTC1485. One way to eliminate
the unwanted current is by AC-coupling the termination
resistors as shown in Figure 13.
Figure 13. AC-Coupled Termination
The coupling capacitor must allow high frequency energy
to flow to the termination, but block DC and low frequen-
cies. The dividing line between high and low frequency
depends on the length of the cable. The coupling capacitor
must pass frequencies above the point where the line
represents an electrical one-tenth wavelength. The value
of the coupling capacitor should therefore be set at 16.3pF
per foot of cable length for 120
cables. With the coupling
capacitors in place, power is consumed only on the signal
edges and not when the driver output is idling at a 1 or 0
state. A 100nF capacitor is adequate for lines up to 400 feet
in length. Be aware that the power savings start to de-
crease once the data rate surpasses 1/(120
C).
Receiver Open-Circuit Fail-Safe
Some data encoding schemes require that the output of
the receiver maintains a known state (usually a logic 1)
when the data is finished transmitting and all drivers on the
line are forced into three-state. The receiver of the LTC1485
has a fail-safe feature which guarantees the output to be in
a logic 1 state when the receiver inputs are left floating
(open-circuit).
If the receiver output must be forced to a known state, the
circuits of Figure 14 can be used.
Figure 14. Forcing “0” When All Drivers Are Off
1485 F14
110
RX
130
130
110
5V
RX
1.5k
120
5V
1.5k
RX
RECEIVER
120
5V
C
100k
RECEIVER
RECEIVER
1485 F13
C = LINE LENGTH (FT) 16.3pF
120
C
RX
RECEIVER
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1485 | Differential Bus Transceiver |
| LTC1485C | Dual, Micropower, LinCMOS(TM) Voltage Comparator 8-PDIP 0 to 70 |
| LTC1485CN8 | Differential Bus Transceiver |
| LTC1485CS8 | Differential Bus Transceiver |
| LTC1485I | Differential Bus Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1490 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual and Quad Micropower Rail-to-Rail Input and Output Op Amps |
| LT1490A | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual/Quad Over-The-Top Micropower Rail-to-Rail Input and Output Op Amps |
| LT1490A_1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual/Quad Over-The-Top Micropower Rail-to-Rail Input and Output Op Amps |
| LT1490ACDD | 功能描述:IC OPAMP R-R IN/OUT DUAL 8DFN RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:Over-The-Top® 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
| LT1490ACDD#PBF | 功能描述:IC OPAMP R-R IN/OUT DUAL 8DFN RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:Over-The-Top® 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
發布緊急采購，3分鐘左右您將得到回復。